PerkinElmer OilExpress System Скачать руководство пользователя страница 83

Страница: 83 / 102

Routine Maintenance and Troubleshooting . 83

Push the insulation block cable through the back end of the arm until the gold

connector is visible.

o l d C

o a x C

o n n e c t o r

Figure 33 Disconnecting the insulation block cable

Disconnect the insulation block cable from the connector.

Carefully pull the insulation block cable back out through the back of the arm.

Remove the new insulation block cable and the plastic cable strap from the packaging.

10.

Feed the gold connector of the insulation block cable through the back of the arm.

11.

Attach the gold connector to the matching connector on the ALIDUM cable. Be sure that

the connectors are firmly seated.

12.

Adjust the ALIDUM cable until all of the slack is removed from behind the arm.

13.

Fasten the insulation block cable to the arm using the new plastic cable binder.

14.

Reinstall the sampling probe.

15.

Replace the top cover and retaining screws.

CAUTION

Make sure the insulation block cable is not twisted or kinked.

Содержание OilExpress System







































































































Результаты поиска

Содержание OilExpress System

Отзывы:

Бренды по названию

Популярные бренды

PerkinElmer OilExpress System, Руководство пользователя

Результаты поиска

Содержание OilExpress System

Отзывы:

Бренды по названию

Популярные бренды