PerkinElmer Migele Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 42

background image

Maintenance

Warning:

Disconnect the external power supply before cleaning or servicing.

Daily maintenance

This section includes instructions for the daily maintenance of the Migele Gel Electrophoresis Unit.

Cleaning the cooling plate

Wipe the cooling plate with watered paper towel (lint-free paper towel) and dry it. It is recommended to clean the

cooling plate immediately after the run, and if required, also before the run. Solvents and detergents should not be

used in cleaning the cooling plate surface. See the pictures below for more details.

Figure 24: Cleaning the cooling plate and lid

Lid

When not used, leave the lid in the idle position (stand by) to ventilate the cooling plate and electrodes. This can be

monitored at the front panel of the instrument (with the green spot indicating the "locked" running position (see

18: Locked position indicated by green spot visible

2118-0010 - Migele

®

Gel Electrophoresis Unit User Manual

Maintenance

26

«
...
28
29
30
31
32
...
»

Содержание Migele











































Отзывы:

Нет отзывов

Похожие инструкции для Migele

Бренд: Yamaha Страницы: 50

Бренд: A&D Страницы: 30

Бренд: Ace Страницы: 17

Бренд: ACE INSTRUMENTS Страницы: 33

Бренд: ACE INSTRUMENTS Страницы: 2

Бренд: ACE INSTRUMENTS Страницы: 2

Бренд: TapFlo Страницы: 35

Бренд: DANA Страницы: 8

Бренд: 2E Страницы: 6

Бренд: Warehouse-lighting Страницы: 3

Бренд: E2S Страницы: 5

Бренд: ICP DAS USA Страницы: 45

Бренд: Latham Страницы: 4

Бренд: SafeWaze Страницы: 23

Бренд: ParaBody Страницы: 6

Бренд: ParaBody Страницы: 11

Бренд: Tar River Страницы: 44

Бренд: Tar River Страницы: 61

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды