PerkinElmer Migele Скачать руководство пользователя страница 22

Страница: 22 / 42

Figure 13: Connect the power supply and the Migele Gel Electrophoresis Unit

Connect the power supply and the Migele Gel Electrophoresis Unit with the red and black wires according to the

pictures. EPS 3501 XL requires 4/2 mm adapters in the power supply end.

Connecting the cooling system (multiple units)

One circulating water bath can be used with maximum of four Migele Gel Electrophoresis Units.
Connect the units in series with the attached tubing.

Caution:

Ensure that tubing is not bent too severely (kinked). This blocks the coolant flow, and gel run may be

affected.

Stacking several GEUs

Connect the GEUs together with the supplied clamp. Connect the lowest unit also to the bench table.
Connect the GEUs in series with the attached tubing (stacking). Up to four units can be stacked.

Caution:

Ensure that tubing is not bent too severely (kinked). This blocks the coolant flow, and gel run may be

affected.

See the pictures below for more details.

2118-0010 - Migele

Gel Electrophoresis Unit User Manual

Installation

Содержание Migele











































Результаты поиска

Содержание Migele

Отзывы:

Похожие инструкции для Migele

Бренды по названию

Популярные бренды

PerkinElmer Migele, Руководство пользователя

Результаты поиска

Содержание Migele

Отзывы:

Похожие инструкции для Migele

Бренды по названию

Популярные бренды