PerkinElmer CLARUS 590 GC Скачать руководство пользователя страница 125 | Manualshive

Страница: 125 / 284

PerkinElmer CLARUS 590 GC Скачать руководство пользователя страница 125

FID Overview . 125

5.

After purging the FID with hydrogen for a minimum of 60 seconds observe the signal icon directly

below the

Heater Off

button

.

NOTE: The signal level in mV before the flame ignites.

6.

Pressing the Ignite button

.

7.

Quickly turn the air on by turning the outer knob of the air control valve

fully

counterclockwise.

8.

When you hear a “pop” sound, observe the

Signal

level

in

mV

(as 0.52 mV) as it increases

on the screen and remains greater than the previously noted amount.
You can also confirm that the flame is lit by holding a shiny object (such as a mirror or small

wrench) over the FID outlet. Condensation will appear on the object if ignition has occurred.

WARNING

AVERTISSEMENT

The FID outlet is hot! To prevent injury, never place

your hand over the FID outlet.
La sortie FID est chaude! Pour éviter toute

blessure, ne placez jamais votre main sur la prise

FID.

If the Flame Goes Out During a Run

If the flame goes out during a run, the run continues until completion however the data collected is invalid.

When Clarus GC prepares for the next run it, checks for a flame by running the Flameout test. If the Clarus

GC detects that the flame is out, a screen will appear that will indicate that the flame is out.
You must then manually ignite the flame.

NOTE: To prevent condensation from forming on the FID, always turn off the flame (both hydrogen and air gases)

before cooling the detector or turning off the Clarus GC.

«
...
123
124
125
126
127
...
»

Содержание CLARUS 590 GC





























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды