PerkinElmer CLARUS 590 GC Скачать руководство пользователя страница 114

Страница: 114 / 284

114 . Clarus 590 GC User’s Guide

Set the Air and Hydrogen Flow s

The FID pneumatics utilizes two PPC modules: one to control the air and the other to control the hydrogen.

You set the PPC controlled air and hydrogen flow from the Clarus GC touch screen. Each PPC module is

calibrated at the factory with the gas (air and hydrogen) that it controls; therefore, to set the gas flow,

simply follow this procedure. Turn on the air at the source and adjust the line pressure to 70 - 90 psig.

Turn on the hydrogen at the source and adjust the line pressure to 60 - 90 psig.

Press the

Tools

button and select

Configuration

The Configuration screen, similar to the one below, appears:

Touch the detector button labeled

FIDW

NOTE: FIDW indicates the wide range FID is installed.

The configuration screen for the FIDW detector appears:

NOTE: The screen above shows that an FIDW is installed on Channel A.

Select a filter value from the

Filter

drop-down menu.

Содержание CLARUS 590 GC





























































































































































































































































































Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Бренды по названию

Популярные бренды

PerkinElmer CLARUS 590 GC, Руководство пользователя

Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Бренды по названию

Популярные бренды