PerkinElmer CLARUS 590 GC Скачать руководство пользователя страница 100

Страница: 100 / 284

100 . Clarus 590 GC User’s Guide

Controlling the Autosampler

NOTE: The autosampler will not respond to commands if the autosampler door is opened.

IMPORTANT: Only sample vials and syringes distributed by PerkinElmer should be used with the Clarus GC.

Plungers are not interchangeable from syringe to syringe.

The autosampler contains three basic parts: a syringe tower, a carousel, and a sample tray (see the

following two figures). The

syringe tower

can contain either a 0.5-, 5.0-, or 50.0-

L syringe.

Autosampler Trays and Carousel

The

Clarus 590 GC

is designed to use the large capacity 108-vial tray for standard vials. There is also an

82-vial Thermostatting Tray Kit available for use with the Clarus. The Standard vials are recommended and

supplied by PerkinElmer.

Содержание CLARUS 590 GC





























































































































































































































































































Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Бренды по названию

Популярные бренды

PerkinElmer CLARUS 590 GC, Руководство пользователя

Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Бренды по названию

Популярные бренды