background image

AIR POWERED ABRASIVE SPOT BLASTER

Stock Number M545

SPECIFICATIONS:

Nozzle diameter:    .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 5 mm

Hopper capacity:  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 17 .2 fl . oz . (510 ml)

Maximum air pressure :   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 90 PSI

Air consumption:   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 6 CFM @ 90 PSI

Air inlet:    .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 1/4" NPT

Weight:    .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 14 oz . (0 .4 kg)

Specifications are subject to change without notice .

WARNING!

READ, UNDERSTAND AND FOLLOW ALL INSTRUCTIONS AND 

WARNINGS BEFORE OPERATING THIS TOOL. FAILURE TO DO SO 

MAY RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE AND 

WILL VOID WARRANTY.

Some dust created by sand blasting contains chemicals known to the State of California to cause cancer, birth defects or 

other reproductive harm. An example of this type of chemical is lead from lead based paints, Crystalline Silica from bricks 

and cement or other masonry, Arsenic and Chromium from chemically treated lumber. Your risk from these exposures varies, 

depending  on how often  you do this type of work. To reduce your exposure: work in a well ventilated area and work with 

approved safety equipment, such as dusk masks that are  specially designed to filter out microscopic  particles.

MANUAL

Содержание M545








Отзывы:

Похожие инструкции для M545