manualshive.com logo in svg

Performance Motion Devices Juno MC71112, Руководство пользователя

Поделиться
Скачать
Performance Motion Devices Juno MC71112 Скачать руководство пользователя страница 56

Current Loop

56

Juno Step Motor Control IC User Guide 

9

9.1

Settable Parameters

The table below summarizes the settable parameters for the Juno current loop.

For more information on Juno host commands refer to the 

Juno Velocity & Torque Control IC Programming Reference

.

9.2

Signal Processing

The following table shows the signals that are used to input the current measurement:

Signals representing the instantaneously measured current of each coil leg are input in a voltage range of 0.0 to 3.3V 
with a voltage of 0.0 representing the largest possible negative measured current, a voltage of 1.65V representing a 
measured current of 0, and a voltage of 3.3V representing the largest possible positive measured current.

Current sensors consist of sense resistors, as shown in 

Figure 9-2

, or linear Hall sensors. If sense resistors are used 

ground-referenced operational amplifiers may be used. 

Current inputs are sampled by Juno at a rate of 20 kHz and should be filtered to minimize noise. A low pass filter with 
a rolloff of 200 kHz - 1,000 kHz is recommended, with 500 kHz being a typical value for most applications. MC78113s 
operating at 20 kHz PWM frequency in high noise environments may consider a rolloff on the lower end of the 
frequency range. Juno’s operating with PWM frequencies of 40 kHz, 80 kHz, or 120 kHz operating in low or normal 
noise environments may consider a rolloff on the higher end of this range.

Parameter

Host Command 

Mnemonic

Range & Description

Set Operating 
Mode register

SetOperatingMode

Specified value is a bit-oriented mask determining the 
state of the command source, current loop, and motor 
output enable/disable flags.

Kp

SetFOC

Three parameter command, the first specifies whether 
the provided gain applies to the D loop, the Q loop, or 
both. The second must be 0, and the third has a range of 0 
to 32,767 and specifies the proportional gain value.

Ki

SetFOC

Three parameter command, the first specifies whether 
the provided gain applies to the D loop, the Q loop, or 
both. The second must be 1, and the third has a range of 0 
to 32,767 and specifies the integral gain value.

Ilimit

SetFOC

Three parameter command, the first specifies whether 
the provided gain applies to the D loop, the Q loop, or 
both. The second must be 2, and the third has a range of 0 
to 32,767 and specifies the integrator sum limit.

Pin Name

64-Pin 

TQFP 

Pin#

56-Pin 

VQFN 

Pin#

Description

CurrentA

14

12

Measured Current for Leg current input A

CurrentB

19

16

Measured Current for Leg current input B

CurrentC

12

10

Measured Current for Leg current input C

CurrentD

21

18

Measured Current for Leg current input D

Содержание Juno MC71112



















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды