manualshive.com logo in svg

Performance Motion Devices Juno MC71112, Руководство пользователя

Поделиться
Скачать
Performance Motion Devices Juno MC71112 Скачать руководство пользователя страница 50

Microstep Waveform Generation

50

Juno Step Motor Control IC User Guide 

8

8.5

Settable Parameters

The table below provides a summary of the user-programmable parameters described in this chapter:

For information on the SPI watchdog timer see 

Section

 

8.6.2.1, “Watchdog Timer.”

 

8.6

Signal Processing

8.6.1

Pulse & Direction Signal Interfacing

Pulse

 & 

Direction

 along with 

AtRest

 input is supported by all members of the Juno step motor ICs. These signals are digital 

TTL level, so for typical cable-based connection buffering circuits are recommended.

The table below provides a summary of the pulse & direction related signals:

Parameter

Host Command 

Mnemonic

Range & Description

Set Operating Mode 
register

SetOperatingMode

Specified value is a bit-oriented mask determining the state of 
the command source, current loop, and motor output enable/
disable flags.

Position command 
source

SetDriveCommandMode

Specified value is a fixed code and selects either pulse & direc-
tion, SPI direct input, or the profile generator as the position 
command source.

Microsteps per full 
step

SetCommutationParameter

Two parameter command, the first must be 0 and the second 
has a range of 1 to 1,024 and sets ‘phase counts’, which is four 
times the number of microsteps per full step

Drive current

SetCurrent

Specified value has a range of 0 to 32,767 and determines the 
step motor's drive current command. To convert to % of 
maximum output multiply by 100/32,767.

Holding current

SetCurrent

Specified value has a range of 0 to 32,767and determines the 
step motor's holding current command. To convert to % of 
maximum output multiply by 100/32,767.

Encoder to microstep 
ratio

SetEncoderStepRatio

Two specified values each have a range of 1 to 32,767. The 
first parameter specifies the number of encoder counts per 
motor rotation, the second parameter specifies the number 
of microsteps per motor rotation.

Position error limit

SetLoop

Two parameter command, the first must be 263 and the sec-
ond has a range of 0 to 2,147,483,648 and sets the threshold 
of the difference, in microsteps, between the commanded 
position and the encoder-measured actual position.

Actual position units

SetActualPositionUnits

Specified value is a fixed code and selects encoder counts or 
microsteps as the units of the actual position register.

Watchdog countdown 
timer

SetDriveFaultParameter

Two parameter command, the first must be 3 and the second 
has a range of 0 to 32,767 and sets the watchdog timeout 
interval in units of cycles.

Pin Name

64-Pin TQFP 

Pin#

56-Pin 

VQFN Pin#

Description

Pulse

33

29

Pulse provides a step pulse) signal for the pulse & direc-
tion position command input source.

Direction

36

31

Direction indicates the direction of motion for the pulse 
& direction position command input source.

Содержание Juno MC71112



















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды