NOTA - Este es un manual de Instruciones basico que cubre varios modelos de pistolas de grasa. Las
ilustraciones de abajo puenden no ser exactamente iguales que su pistola especifica.
1. Desatornille la tapa
del barril de la pistola
girando en dirección
opuesta a las manec-
illas del reloj. (Fig. 1)
NOTA - Debido a la
escasa lubricacion del
piston de goma, puede
ser dificil llenar la primera vez de grasa los cartuchos. Aplique una capa suficiente de grasa a el piston cuando se
usa la pistola por primera vez.
Esta pistola de grasa requiere un cartucho de grasa de 397 g
2. Jale completamente el mango hacia atras para que
la cabeza del piston se asegure en su lugar (Fig. 2)
PRECAUCIÓN: Si se jala el sujetador del seguro al
estar vacio, causa que el mango haga repentinamente
para atras.
3. Despues de remover la tapa de plastico del cartucho
de grasa, aplique una pequeña cantidad de grasa al borde
interior del cartucho. (Fig. 3)
4. Empuje el cartucho de grasa hacia el barril completamente, hasta que el metal selle con la parte superior
de la pistola de grasa. Retire el sello de arriba del cartucho. (Fig. 4)
NOTE - Because they
lack lubrication on the
rubber plunger, new
grease guns may be
difficult to load with grease cartridges the first time. Apply a liberal coating of grease to
plunger when using gun for the first time. This grease gun requires a 14 oz. grease cartridge.
2. Draw handle back fully so that the plunger rod
catches and locks into place. (Figure 2)
CAUTION: Depressing the lock release when
empty causes the handle to snap back quickly.
3. After removing the plastic cap from the grease
cartridge, apply a small amount of grease to the
inside edge of the cartridge. This will make insertion
of the plunger easier. (Figure 3)
4. Push grease cartridge into gun barrel completely, until metal edge tightly seals on top of
the grease gun barrel. Detach flip-top seal from cartridge. (Figure 4)
NOTE - This is a basic instruction manual which covers various models of grease guns.
The illustrations below may not depict exactly your specific gun.
1. Rotating counter
clockwise, unscrew
Head Cap from gun
Barrel. (Figure 1)
5. Atornille la cabeza de la tapa aproximadamente dos vueltas, asegurandose que no apriete.Saque el piston
de su posición asegurada. Empuje el mango para forzar la cabeza del piston contra el cartucho. Al mismo
tiempo, bombee el mango para liberar el aire. Cuando la grasa salga de los extremos de la pistola, Apriete la
cabeza de la tapa contra al barril.
6. Al momento que la pistola bombee grasa, cuidadosamente
jale el sujetador del seguro y empuje la cabeza del piston de
vuelta en la pistola.
GREASE CARTRIDGE LOADING
5. Screw on head cap approximately two turns, being sure not to tighten. Release plunger
rod from its locked position and push in. Push on plunger rod handle to force plunger into
cartridge. At the same time, pump the lever or handle to release trapped air. When grease
comes through vents and the head of the gun, fully tighten the head cap to the barrel.
6. As soon as the gun is pumping grease, carefully depress
the lock release and push plunger rod back into gun.
Figure 4
Flip-top Tab
Figure 2
Plunger
Handle
Lock
Release
Figure 3
Barrel
Plastic Cap
Grease Cartridge
Head Cap
Barrel
Bleeder Valve
Figure 1
NOTE - Used cartridges must be removed prior to bulk loading.
1. Make sure the valve is compatible with the adapter
on the pump. (Figure 5)
2. Attach the filler valve to the adapter by pushing in
and rotating slightly.
3. Operate the pump handle while holding the gun
firmly to the pump. As the grease pumps into the
grease gun barrel the plunger handle will extend.
Loading is complete when the plunger rod is fully
extended.
4. A slight twist of the gun will detach it from the pump.
Depress lock release and push the plunger rod back
into the gun.
BULK LOADING WITH DISPENSER
DO NOT REFILL
USED CARTRIDGES
PARA LLENAR CARTUCHO DE GRASA
NOTA - Los cartuchos usados de deben remover antes de ser recargados en volumen.
1. Asegurese que la válvula sea compatible con el adaptador en la bomba. (Fig. 5)
2. Sujete la válvula de relleno al adaptador empujandola y rotando ligeramente.
RELLENO EN VOLUMEN CON DISPENSADOR
NO RELLENE CARTUCHOS USADOS
¡PRECAUCIÓN!
WARN I NG !
Figure 5
NOTE - Used cartridges must be removed prior to suction filling.
1. Remove the gun head cap from the barrel.
2. Submerge open end of the barrel into grease bucket. Be sure
the plunger handle is depressed completely. Grasp the barrel
firmly and pull back slowly on the plunger handle. Be sure the
mouth of the barrel is always under the surface so that air is not
transferred into the barrel. (Figure 6)
3. Loading is complete when plunger rod is fully extended.
4. Reattach the gun head cap to the barrel. Depress lock release
and push the plunger rod back into the gun.
NOTE - Grease guns may lose their prime on occasion, because of air pockets in the grease.
If this occurs, remove the trapped air by bleeding the head cap and resume pumping.
Figure 6
SUCTION FILLING
Tapa de Cabeza
Barril
Válvula de desahogo
Fig. 1
Fig. 2
Mango
de Piston
Sujetador
de Seguro
Fig. 4
Tapa Quita-pon
Fig, 3
Barril
Tapa de Plástico
Cartucho de Grasa
Bulk Load
Filler Valve
