PERCo IC-05 Скачать руководство пользователя страница 27

Страница: 27 / 34

Assembly and Operation Manual

19.

Attention!

If the passage permission indication of the card capture reader is controlled

directly from the control board of the turnstile, then, it is not necessary to fulfill

the requirements of this paragraph.

In the left part of the working area, select the

"Additional outputs, activated during

the OD unblocking"

parameter and set:



set

"For the operation time"

value for the

"Activation criteria"

parameter by

using the drop-down list.



in the appeared list of additional outputs check

"Additional output

№..."

(number of the output that is physically connected to the

“LED”

input of the card

capture reader).

Now, the ACS-controller will always switch on the permission indication on the card

capture reader when you unlock the OD in this direction.

20. Click

"Save and close"

button. The

"Device properties"

window will be closed all

settings will be saved.

Appendix 2. Configuring in the Web interface CT/L-04.2,

CT-03.2 for working with the card capture reader

Attention!

You can configure the most basic algorithm of cards withdrawal by using the Web

interface. Advanced options are available in

PERCo-Web

software.

CT/L-04

(

CT-

) controllers don't support operation with the card capture reader via Web-

interface.

1. In

"Configuration"



"Edit"



"Operating devices"

section, select the OD that is

physically connected to the card capture reader, then select

"Reader 1"

"Reader 2"

depending on the direction of the passage that is controlled by the card

capture reader. Set the following parameters for the reader:



set

the

"External verification device"

value for the

"Verification"

parameter,



within the

"External device verification in ACM "Control"

group of parameters

set

"Yes"

value

for the

"Visitor pass verification"

parameter

and

also set the

required values

for

"Visitor verification activation"

and

"External device

verification waiting period"

parameters.

2. Set the following parameters in

"Configuration"



"Edit"



"Physical contacts"

section:



set the following parameter values for input that is physically connected to the “Card

captured” output of the card capture reader:

"Normal state:"

–

"Cut"

"Function:"

–

"External verification device confirmation input"

"Operating device:"

–

"1"

(number of OD that is physically connected to the

card capture reader),

Содержание IC-05



































Результаты поиска

Содержание IC-05

Отзывы:

Бренды по названию

Популярные бренды

PERCo IC-05, Руководство по сборке и эксплуатации

Результаты поиска

Содержание IC-05

Отзывы:

Бренды по названию

Популярные бренды