Pepperl+Fuchs IC-KP-B7-V95 Скачать руководство пользователя страница 66

Страница: 66 / 98

-0

IC-KP-B7-V95

Commands

7.6

Fault/Status messages

Error messages triggered by the identification system

<Month>

:2 bytes ASCII, hexadecimal encoding, 01 ... 0C (01=January,

0C=December)

<P>

:1 bit, password mode, 0 (0b): Mode off, 1 (1b): Mode on

<PW>

:4 bytes HEX, password

:1 byte, increases by 1 after each response and confirmation. The

reply counter starts from 0 after the system is switched on. When the

maximum value is reached, the counter skips the value 0 (from 255 to

1).

:3 (011b) or 4 (100b)

:1 byte ()

<T>

:1 bit, toggle bit

:2 ASCII characters, for example: '02' for IPC02

:8 bits

0 (00000000b): Trigger mode off

1 (00000001b): Trigger mode on

2 (00000010b): Trigger mode inverted

:2 bytes, word start address in the data carrier, range from 0000h to

FFFFh, depending on tag type.

:4 bits, number of words to be read or written, range from 0h to Fh,

depending on tag type. The following applies for IPC03: The word

count 0h is used with the word address 0000h to read the preset data

range on the data carrier ("Default Read").

<Year>

:2 bytes ASCII, hexadecimal encoding, 00h ... 63h

Status

Meaning

00h

The command has been executed without error.

FFh

The command is processing.

Status

Meaning

02h

Reserved

03h

Reserved

04h

Incorrect or incomplete command or parameter not in the valid range.

05h

No data carrier in the detection range.

06h

Hardware error, e.g. error during self-test or R/W head defect.

07h

Internal device error.

08h

Reserved

09h

The parameterized tag type is not compatible with the connected reading head.

0Ah

Reserved

0Bh

Reserved

0Ch

Reserved

Содержание IC-KP-B7-V95



































































































Результаты поиска

Содержание IC-KP-B7-V95

Отзывы:

Бренды по названию

Популярные бренды

Pepperl+Fuchs IC-KP-B7-V95, Руководство пользователя

Результаты поиска

Содержание IC-KP-B7-V95

Отзывы:

Бренды по названию

Популярные бренды