Pepperl+Fuchs HiD2022 Series Скачать руководство пользователя страница 17

Functional Safety HiD2022*, KFD2-STC5-(Ex)*, KFD2-STV5-(Ex)*

Planning

20

21

-0

4

17

3.4

Useful Lifetime

Although a constant failure rate is assumed by the probabilistic estimation this only applies 

provided that the useful lifetime of components is not exceeded. Beyond this useful lifetime, 

the result of the probabilistic estimation is meaningless as the probability of failure significantly 

increases with time. The useful lifetime is highly dependent on the component itself and 

its operating conditions 

 temperature in particular. For example, electrolytic capacitors can 

be very sensitive to the operating temperature.
This assumption of a constant failure rate is based on the bathtub curve, which shows 

the typical behavior for electronic components.
Therefore it is obvious that failure calculation is only valid for components that have 

this constant domain and that the validity of the calculation is limited to the useful lifetime 

of each component.
It is assumed that early failures are detected to a huge percentage during the installation 

and therefore the assumption of a constant failure rate during the useful lifetime is valid.
However, according to IEC/EN 61508-2, a useful lifetime, based on general experience, 

should be assumed. Experience has shown that the useful lifetime often lies within a range 

period of about 8 to 12 years.
As noted in DIN EN 61508-2:2011 note N3, appropriate measures taken by the manufacturer 

and plant operator can extend the useful lifetime.
Our experience has shown that the useful lifetime of a Fuchs product can be higher 

if the ambient conditions support a long life time, for example if the ambient temperature 

is significantly below 60

°

C.

Please note that the useful lifetime refers to the (constant) failure rate of the device. 

The effective life time can be higher.
The estimated useful lifetime is greater than the warranty period prescribed by law 

or the manufacturer's guarantee period. However, this does not result in an extension 

of the warranty or guarantee services. Failure to reach the estimated useful lifetime is not 

a material defect.

Содержание HiD2022 Series



























Отзывы: