peplink Pepwave MAX Series Скачать руководство пользователя страница 170

Страница: 170 / 218

https://www.peplink.com

Revision

Serial Number

This shows the serial number of this device.

Firmware

This shows the firmware version this device is currently running.

PepVPN Version

This shows the current PepVPN version.

Modem Support

Version

This shows the modem support version. For a list of supported modems, click

Modem Support List

InControl

Managed

Configuration

InControl Managed Configurations (firmware, VLAN, Captive Portal, etcetera)

Host Name

The host name assigned to the Pepwave router appears here.

Uptime

This shows the length of time since the device has been rebooted.

System Time

This shows the current system time.

OpenVPN Client

Profile

Link to download OpenVpn Client profile when this is enabled in Remote User

Access

Diagnostic

Report

The

Download

link is for exporting a diagnostic report file required for system

investigation.

Remote

Assistance

Click

Turn on

to enable remote assistance.

The second table shows the MAC address of each LAN/WAN interface connected. To view your
device’s End User License Agreement (EULA), click

Legal

30.2

GPS Data

GPS enabled models automatically store up to seven days of GPS location data in GPS

eXchange format (GPX). To review this data using third-party applications, click

Status

Device

Содержание Pepwave MAX Series




































































































































































































Результаты поиска

Содержание Pepwave MAX Series

Отзывы:

Похожие инструкции для Pepwave MAX Series

Бренды по названию

Популярные бренды

peplink Pepwave MAX Series, Руководство пользователя

Результаты поиска

Содержание Pepwave MAX Series

Отзывы:

Похожие инструкции для Pepwave MAX Series

Бренды по названию

Популярные бренды