SELECTING A LIGHT SHOW OR FIXED COLOR (CONT’D)
FIXED COLORS
• Blue: Fixed color.
• Green: Fixed color.
• Red: Fixed color.
• White: Fixed color.
• Magenta: Fixed color.
Hold and Recall Feature:
Note: When the
IntelliBrite LED light(s) are powered on, a white
light will momentarily illuminate, followed by
the selected color, unless the HOLD or RECALL
feature was previously enabled.
LIGHT SHOW MODE
• SAm Mode: Cycles through white, magenta, blue and green
colors (emulates the Pentair Water Pool and Spa SAm
®
Color Changing Light).
• Party Mode: Rapid color changing building energy and excitement.
• Romance Mode: Slow color transitions creating a mesmerizing and
calming effect.
• Caribbean Mode: Transitions between a variety of blues and greens.
• American Mode: Patriotic red, white and blue transition.
• California Sunset Mode: Dramatic transitions of orange, red and
magenta tones.
• Royal Mode: Richer, deeper color tones.
INTELLIBRITE
®
5G LED LIGHT
FOR INTELLIBRITE POOL, SPA AND LANDSCAPE LIGHTING FIXTURES
OVERVIEW
QUICK REFERENCE GUIDE
Hold button/LED:
Press this button (LED on) to capture and
save a color effect while displaying one of the light show
modes. When the button is pressed, the LED will be on,
indicating that the color effect is captured.
Recall Button/LED:
Use this button (LED on) to activate the
last saved color effect. When the button is pressed, the LED
will be on, indicating that the color effect is being displayed.
CONTROLS AND
BUTTONS
The IntelliBrite Controller
controls, buttons and LEDs
are shown below:
Power ON/OFF Switch
RECALL button and LED
Dial and Color Show and
Fixed Color Selections
Door
HOLD button
and LED
PRINTED ON: 7/29/2009, 600054_ctlg pics.SLDASM
TROUBLESHOOTING
PROBLEM
CAUSE/ACTION
Both of the LEDs are
flashing.
The IntelliBrite Controller has detected that the load has exceeded the maximum allowable
wattage or the output is shorted out
1. Switch of the IntelliBrite Controller OFF. Remove excessive load or short.
2. Press the IntelliBrite Controller power switch to power on the unit. Ensure that the LEDs
are no longer flashing.
The light will not illuminate.
Light does not function
properly.
Check the ground fault wiring and reset if necessary.
Check the light wiring connection to the junction box at the pool side and to the main circuit breaker.
Be sure that there is proper AC power applied to the light.
To select a color light show mode or fixed color mode, rotate the dial so that it points to the desired selection.
Hold and Recall Feature:
When IntelliBrite color lights are powered on, the previously selected color will be displayed, unless
the HOLD or RECALL feature was previously enabled.
Hold button/LED:
Press this button (LED on) to capture and save a color effect while displaying one of the light show modes.
When the button is pressed, the LED will be on, indicating that the color effect is captured.
Recall Button/LED:
Use this button (LED on) to activate the last saved color effect. When the button is pressed, the LED will
be on, indicating that the color effect is being displayed.
The following describes how to install the IntelliBrite 5G Color LED Pool Light. The IntelliBrite 5G color LED light provides brilliant vivid
multi-colors with spectacular effects for your pool. Choose one of the seven pre-programmed color light shows or select one of the
five fixed colors to create virtually endless range of dramatic underwater lighting effects for a spectacular effect in your pool. There
are two ways to control IntelliBrite 5G Color Pool Lights; Using the IntelliBrite Controller (page 1) or using a Wall Switch (page 2).
Operating Lights Using an IntelliBrite Controller
: The IntelliBrite
®
Controller provides complete control of
IntelliBrite
underwater LED (light-emitting diode) lights, and IntelliBrite LED landscape lights. It’s easy to select a lighting feature, just dial
in any one of the pre-programmed color light shows or fixed colors. Using the Hold and Recall buttons you can also create endless
unique lighting effects. The IntelliBrite Controller can control individual or multiple IntelliBrite LED lights. Multiple IntelliBrite
LED lights can be connected via a junction box to an IntelliBrite Controller so that all lights can be switched on and off together.
IntelliBrite LED lights are fully compatible with Pentair IntelliTouch
®
and EasyTouch
®
Control Systems. For more information
about using IntelliBrite lights with IntelliTouch systems, refer to the IntelliTouch User’s Guide (P/N 520102) and the EasyTouch
User’s Guide (P/N 520584).
SELECTING A LIGHT SHOW OR FIXED COLOR
Note: When the IntelliBrite LED light(s) are powered on, a white light will momentarily illuminate, followed by the selected color, unless
the HOLD or RECALL feature was previously enabled. To select a color light show mode or fixed color mode, rotate the dial so that it
points to the desired selection. The color mode selections are described to the right starting clockwise from the 9 o’clock position:
ppw229_instructioncard_FINAL.indd 1
6/13/17 8:00 PM
