Pentair Hydrel Fixture Housing Скачать руководство пользователя страница 1

Rev. A  1-18-06

1

P/N  620001

Hydrel Fixture Housing -

Rust Staining Repair Instructions

Before installing this product, read and follow all warning notices and instructions accompanying this product.
Failure to follow safety warnings and instructions can result in severe injury, death, or property damage. Call
(800) 831-7133 for additional free copies of these instructions.

IMPORTANT SAFETY INSTRUCTIONS

READ AND FOLLOW ALL INSTRUCTIONS

SAVE THESE INSTRUCTIONS

Important Notice

Attention Installer.
This manual contains important information about the installation, operation and safe use of
this product. This information should be given to the owner/operator of this equipment.

Pentair Water Pool and Spa™

1620 Hawkins Ave., Sanford, NC 27330 • (919) 556-8000
10951 West Los Angeles Ave., Moorpark, CA 93021 • (805) 553-5000

Risk of Electrical Shock or Electrocution.

Always disconnect power to the pool light at the circuit breaker before servicing the light. Failure to
do so could result in death or serious injury to installer, serviceman, pool users or others due to
electrical shock.

 WARNING

DANGER

 WARNING

Never operate this underwater light for more than 10 seconds unless it is totally submerged in water. Without total
submersion, the light assembly will get extremely hot, which may result in serious burns or in breakage of the lamp or
lens. This may result in serious injury to pool users, installers, or bystanders, or in damage to property.

 WARNING

Use only the special pilot screw provided with this underwater light. This screw mounts and electrically
grounds the housing securely to the mounting ring and wet fixture housing. Failure to use the screw
provided could create an electrical hazard which could result in death or serious injury to pool users,
installers or others due to electrical shock. This procedure can be performed with the water in the pool.

Contents

SECTION I.

FIXTURE HOUSING ENTRY HUB REPAIR INSTRUCTIONS.  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

SECTION II.

ALTERNATE REPAIR INSTRUCTIONS,  BEFORE 1998.  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Содержание Hydrel Fixture Housing

















Отзывы: