manualshive.com logo in svg

Pentair FLECK 9100 SXT, Руководство по установке

Поделиться
Скачать
Pentair FLECK 9100 SXT Скачать руководство пользователя страница 63

Installer manual Fleck 9100 SXT - Operation

Ref. MKT-IM-004 / E - 06.10.2020 

63 / 108

8.2

Recommendations

• Use only regeneration salts designed for water softening in accordance with EN973;

• for optimal system operation, the use of clean salt, free from impurities, is recommended (for

example salt pellets);

• do not use ice melt, block, or rock salts;

• the sanitizing process (both with liquid and electrochlorination) may introduce chlorine

compounds which may reduce the lifetime of the ion exchange resins. Refer to the technical
guides for resins in common use, providing necessary checks on the system.

8.3

Manual regeneration

Mandatory

The controller must be in service in order to enable this procedure !

8.3.1

Manual delayed regeneration

Info

This option is not available in mode FI.

8.3.2

Immediate regeneration

1. Press and hold 

 for 5 seconds to initiate immediate manual regeneration regardless from

the programmed regeneration control type.

8.3.3

To advance regeneration cycles

1. Press 

 to pass to the next regeneration cycle.

Содержание FLECK 9100 SXT













































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды