Pentair FLECK 9000 SXT Скачать руководство пользователя

Страница: 63 / 118

Installer manual Fleck 9000 SXT - Programming

Ref. MKT-IM-020 / C - 21.11.2019

63 / 118

6.6.7

Software version (SV)

Info

Shows the version of the software used by the controller.

1. Software version display:

6.7

Resetting the controller

Mandatory

Once you have completed this operation, check all programming steps !

Info

There are two options to reset: partial and hard reset.

Partial reset will set all the parameters to default values, except volume remaining in
volumetric systems and days since last regeneration in time clock systems.

Hard reset will set all the parameters to default values.

6.7.1

Soft reset (SR)

1. Press and hold

and

for 25 seconds while in normal

service mode until

is displayed.

6.7.2

Hard reset (HR)

1. Hold

while powering up the unit.

2. The display shows

3. Reprogram all parameters in Master programming mode.

Содержание FLECK 9000 SXT























































































































Результаты поиска

Содержание FLECK 9000 SXT

Отзывы:

Похожие инструкции для FLECK 9000 SXT

Бренды по названию

Популярные бренды

Pentair FLECK 9000 SXT, Руководство по установке

Результаты поиска

Содержание FLECK 9000 SXT

Отзывы:

Похожие инструкции для FLECK 9000 SXT

Бренды по названию

Популярные бренды