Pentair Evolio 255 10 Скачать руководство пользователя

Страница: 44 / 90

Installer manual Evolio 255 740-760 - Programming

44 / 90

Ref. MKT-IM-037 / D - 25.10.2021

Salt setting

Evolio 255 10

Evolio 255 15

Evolio 255 20

Evolio 255 30

45.0

46.7

55.0

53.3

91.0

133.3

160.0

136.7

180.0

226.7

250.0

226.7

1. Press

Setting flashes.

2. Adjust displayed settings with

and

3. Press

to validate the selection and advance to the

next parameter using

5.4.7

Estimated capacity

Info

The system capacity is displayed in kilograms equivalent CaCO

of hardness removed

before a regeneration is necessary when programmed in metric units mode.

Value is derived from the system’s resin volume input and salt amount input and must
be fine tuned for optimal operation.

Set the estimated capacity, in kg as CaCO

, following the following table.

Salt setting

Evolio 255 10

Evolio 255 15

Evolio 255 20

Evolio 255 30

0.3

0.5

0.7

1.0

0.5

0.9

1.4

1.9

0.7

1.2

1.6

2.3

1. Press

The amount number flashes.

2. Adjust displayed capacity with

and

3. Press

to validate the selection and advance to the

next parameter using

5.4.8

Hardness

Set water hardness to treat at installation site in mg/L as CaCO3. Program the value of inlet
hardness taken away from expected residual hardness. For example, if inlet hardness is 300 mg/L
as CaCO

and residual hardness is set to 100 mg/L as CaCO

, set 300-100=200 mg/L as CaCO

Содержание Evolio 255 10



























































































Результаты поиска

Содержание Evolio 255 10

Отзывы:

Похожие инструкции для Evolio 255 10

Бренды по названию

Популярные бренды

Pentair Evolio 255 10, Руководство по установке

Результаты поиска

Содержание Evolio 255 10

Отзывы:

Похожие инструкции для Evolio 255 10

Бренды по названию

Популярные бренды