PenBits PK017 Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 66

PenBits PK017 Скачать руководство пользователя страница 52

Bachmann 'Peak': Wheelsets

The diagram shows the arrangement of
the driving wheelsets. 2mm diameter

axles match with the bearings supplied in the
kits,  and  with  the  gears  of  driven  axles.
Unpowered  axles  can  be  of  other  diameters
(requiring  modification  or  substitution  of  the
be a rings supplied),  e.g.  the  3mm  axles
supplied

in

some

conversion

sets. For

discussion on the possible choices of wheels
and axles, see t he

Description page on the website.

The kit is designed to use full-width solid
steel axles with pickup on one side of each bogie via uninsulated wheels on that side. Pin-
pointed ends should be removed.

At  least  two  wheels  on  one  side  of  each  bogie  should  be  uninsulated. Wheels  from  Alan
Gibson  or  Ultrascale  may  be 'shorted  out'  (i.e.  uninsulated)  by  various  means,  including
those  mentioned  in  the  following  paragraphs. Branchlines  14mm  coach  wheelsets
(insulated  on  one  side)  may  be  used,  as  they  come,  for  the  driving  wheels,  though  they
are  slightly  under-sized. Their  similar  12mm wheelsets  may  be  used  for  the  carrying
wheels, though current stocks (as at November 2016) are insulated on both sides.

We have used this technique on Alan
Gibson wheels. Make a curled end on a

length of phosphor bronze wire and solder  it  to
the  edge  of  one  of  the  2mm  spacing  washers
supplied in the kit. Put a kink in the wire, shape
it so  that  the  the  washer  sits  flat  against  the
wheel  boss  (for the  centre  wheelset  you  might
wish  to  thin  the  boss  a  little)  and  solder it
(very  carefully)  to  the  inside  of  the  (pre-
tinned)  inner  wheel  rim  (make  sure  it's  not
fouling  the  running  part  of the  rim).  A  slight
misaligment will help maintain electrical contact
between the axle and the washer.

Shorting Discs for Ultrascale wheels are
available (to members only) from the

Scalefour Society Stores,

www.scalefour.org

,

and  are  written  up  by  their  designer,  Mark
Humphrys, in  Model  Railway  Journal  No.  248.
W e have  used  these  successfully  and  can
recommend  them.  An  alternative  design  is
available

from

Brassmasters, Ref A403 at

www.brassmasters.co.uk/accessories.htm

.

The photo shows one of Mark's shorting

Bachmann 'Peak': Wheelsets

52/65

(c) PenBits Model Railways, All Rights Reserved

27/09/2021

«
...
50
51
52
53
54
...
»

Содержание PK017



































































Отзывы:

Нет отзывов