background image

PelPro Pellet Stove  •  8104-171B  •  10/21

PelPro Pellet Stove  •  8104-171B  •  10/21

pelprostoves.com

pelprostoves.com

6

7

Installing 

Your 

Stove

Installing 

Your 

Stove

Installing Your Stove

Your Home Acts Like a Chimney

We recommend that you help your home by:

1.  Using a minimum of 5 feet of vertical venting

2.  Use the supplied outside air kit

3. 

Install your Stove on a main floor location 

This will:

•  Help your Stove breathe

•  Minimize smoke leakage in the house

•  Enhance performance

Clearance to Combustibles

The space between your Stove and the items in your home 

that could burn. Materials such as:

•  Wood

• 

Sheet rock (drywall)

•  Carpet

A

A

B

B

G

E

D

Getting Ready

1

2

3

 WARNING!

Asphyxiation Risk.  

DO NOT INSTALL IN A SLEEPING ROOM. Consumes oxygen in the room.

Pro Tip

We highly recommend your Stove and pellet vent pipe be installed by a professional installer. 

Your retailer can make recommendations for you.

Installation MUST comply with local, regional, state and national codes and regulations.

Consult insurance carrier, local building inspector, fire officials or authorities having jurisdic

-

tion over restrictions, installation inspection and permits.

Placement

Where you place your Stove can significantly affect its performance and safety.

For Canada, the installation must conform to CAN/CSA-B365

Installing Your Stove

Getting Ready (Continued)

Pellet Venting 

Adding bends in the exhaust path restricts air flow, reduces 

performance and provides a collection point for ash deposits 

requiring more frequent cleaning.

REQUIRED: 

Use only 3” or 4” type “L” or “PL” pellet pipe.

C

C

 CAUTION

• 

Do not connect to any air distribution duct or system

• 

Do not install a flue damper in the exhaust venting system of this 

Stove

• 

Do not connect this Stove to a chimney flue serving another Stove

• 

The structural integrity of the manufactured home floor, wall and 

ceiling/roof must be maintained

Pro Tip

This Stove can be installed with a 3 to 6 inch (76-152mm) Top Vent Offset Adapter Kit. The 

3 to 6 inch (76-152mm) Top Vent Offset Adapter are tested to use 24 gauge single wall flue 

connector or Listed double wall flue connector to Class A Listed metal chimneys, or masonry 

chimneys meeting International Conference of Building Officials (ICBO) standards for solid 

fuel Stoves.

Caution,

 do not pass connector pipe through a combustible wall or ceiling.  Please refer to 

connector pipe installation instructions for details.

Installation Video 

Visit 

pelprostoves.com

 or scan this code:

Содержание PP150
























Отзывы: