pellenc HELION 3 Скачать руководство пользователя страница 26

Страница: 26 / 36

ELECTRIC HEDGE TRIMMER HELION 3

54_161520-B

7. INCIDENTS AND TROUBLESHOOTING

Important

For any problems concerning the battery, refer to the manual that comes with the battery.

PELLENC recom-

mends contacting an authorised PELLENC dealer in all cases of breakdown.

7.1. TROUBLESHOOTING SYMPTOMS OF THE HELION 3 ELECTRIC HEDGE TRIMMER

Symptom

Check

Probable cause

Solutions

Battery discharged

Charge the battery

Battery defective

Change the battery

Check the power cable

The LEDs are off

Wrong connection

with the battery

Check the connections (tool and

battery) Clean them with com-

pressed air if necessary. Check

that all switches are active. Re-

peat the operation if necessary.

Safety at start-up/

Standby (Delay > 5min)

Double-click the trigger of

the rear handle and pull the

trigger of the front handle.

The On/Off switch-

es are defective

Unplug the power cable and

plug in again. Restart the battery

Cutting blade blocked

Clean and lubricate the blade

The LEDs are lit

Internal loose connection

Contact your autho-

rised PELLENC dealer

The hedge trim-

mer does not work

LEDs flashing

inside/outside

Safety when

switching on

Release the front handle

The LEDs light-

up intermittently

Damaged power cords

Change the power cable

Blade is clogged

Clean and lubricate the blade

The hedge trimmer

works intermittently

The LEDs are always on

The On/Off switch-

es are defective

Contact your autho-

rised PELLENC dealer

Содержание HELION 3





































Результаты поиска

Содержание HELION 3

Отзывы:

Похожие инструкции для HELION 3

Бренды по названию

Популярные бренды

pellenc HELION 3, Руководство по эксплуатации

Результаты поиска

Содержание HELION 3

Отзывы:

Похожие инструкции для HELION 3

Бренды по названию

Популярные бренды