Peg-Perego book cross, Инструкция по эксплуатации, Страница: 17 / 76

difficult terrain, we recommend using fixed wheels.
8 BOOK CROSS BRAKE: To engage the brake, pull the
handle on the handlebar towards you (arrow_a) and
block the red lever (fig_b); to release the brake, release
the lever (arrow_c). Always engage the brake when
stationary. To adjust the brake making it more rigid,
loosen the regulator (fig_d) located on the handlebar by
screwing it outwards. To loosen and soften the brake, do
the opposite.
9 ADJUSTABLE HANDLEBAR: To adjust the height of the
handlebar, press both of the side buttons at the same
time (fig_a) and swing it into the desired position
(fig_b), then release the buttons.
10 FOOTREST: before adjusting the foot rest, ensure its
cover is accurately fitted; if it isn’t, fit it accordingly. To
lower the footrest push the two levers downwards and
then push the footrest downwards (fig_a); to raise the
footrest lift it upwards (fig_b).
11 FRONT BAR: To pull the front bar out by one position,
press the button as shown and pull outwards (fig_a).
To remove the front bar, pull it out to the second
position and remove (fig_b). Open-close front bar: pull
out on one side and rotate.
12 HOOD: The hood comes with a loop for hanging your
child's favorite toy (fig_a) and a see-through window
for observing your child (fig_b), which can be lifted
and fastened. You can detach the Velcro, roll up the
back of the hood and fasten it at the top with the
rubber band to allow greater ventilation during use
with the backrest down (fig_c). The hood may be
pulled forward into several positions (fig_d).
13 ADJUSTING THE BACKREST: to lower the backrest,
press the clip and the backrest will move down to the
desired position.
To raise the backrest, press the clip and lift the
backrest to the desired height.
14 FOOT MUFF: To secure the foot muff to the stroller,
button the rubber band to the side bar (fig_a) and
button the top part of the foot muff to the inside
button (fig_b).
15 FIVE POINT SAFETY HARNESS: To fasten it, push the two
waist strap buckles (with the shoulder straps attached
– arrow_a) into the leg divider until they click into place
(arrow_b). To unfasten it, press the round button in the
centre of the buckle (arrow_c) and pull the waist straps
out (arrow_d).
16 To tighten the waist strap, pull on both sides in the
direction of the arrow (arrow_a). To loosen it, move it
in the opposite direction.
17 Before adjusting the height of the safety harness
remove the shoulder pads (fig_a). To adjust the height,
slip the belts through the eyelet in the fabric (fig_b)
and position them in the most suitable eyelet.
18 FOLDING UP: To fold up the stroller, we recommend
ensuring the front wheels swivel, closing the hood,
removing the car seat when fastened.
- Align the handlebar and frame as shown in the figure
(fig_a).
- Push the inside folding handle downwards (fig_b),
checking that the fastener has been released.
- Pull both handles towards you (fig_c), and whilst
maintaining the same grip, lift the frame (fig_d).
19 Allow the handlebar to fall in on itself until fully folded
(fig_e).
The frame is folded correctly when the side fastener
automatically locks (fig_f). Otherwise, gently press
down on the frame (fig_g).
The stroller is free-standing when folded.
20 For greater compactness, it is possible to remove the
wheels.
To remove the rear wheels: pull the pivot outwards and
remove the wheel as shown in the figure (fig_a).
To remove the front wheels: press the tab as shown, and
remove the wheel (fig_b).
TRANSPORT: the stroller can be carried comfortably locking
the front wheels and grasping the main handle (fig_c).
21 REMOVABLE ITEMS: to remove the hood, take the
elastic off from the buttons on the inside of the
handlebar (fig_a), detach the press studs the sides of
the chassis (fig_b), detach the Velcro strip from the
backrest (fig_c) and remove the attachments of the
hood from their positions on the chassis (fig_d).
22 To remove the seat fabric, press in the holes on the
inside of the chassis (fig_a); remove, from the side of
the seat, the rigid flap of the chassis fabric ((fig_b),
unfasten the elastic of the net from the side buttons
inside the handlebar (fig_c) and unfasten the elastics
from the buttons inside the chassis (fig_d).
23 Slip the cover off the footrest from the front (fig_a),
pull the crotch strap out from below the seat (fig_b),
unhook the rubber band from the seat’s side hook
(fig_c), unscrew the waist strap (fig_d) and remove the
cover from the backrest (fig_e).
GANCIOMATIC SYSTEM
The Ganciomatic System is the quick, practical system
that allows you to fasten the Navetta Pop-Up /
Navetta XL / Navetta Elite and the Primo Viaggio SL
car seat (sold separately) onto the stroller using the
Ganciomatic hooks.
24 GANCIOMATIC HOOKS ON THE STROLLER: to lift the
stroller's Ganciomatic hooks, pull back the fabric at the
corners of the seat.
Pull the frame's side levers outwards (fig_a) and turn
the Ganciomatic hooks upwards.
_ To lower the hooks, proceed in the opposite order.
Primo Viaggio SL can be mounted on the stroller
version of Book Cross with the backrest attached, or on
the Naked version (i.e. chassis version).
Navetta Pop-Up / Navetta XL / Navetta Elite can only
be mounted on the Naked version (i.e. the chassis
version).
To transform Book Cross into Naked, chassis version,
you must:
25 Remove the hood and the seat fabric from the stroller
(up to point C in figure 24); press the buttons under the
seat fabric at the base of the backrest (fig_a) on both
sides. Remove the backrest by lifting it upwards (fig_b).
_ To transform the chassis back into the stroller version,
repeat the operations listed above in the opposite
order.
26 When the stroller is in the Naked version, pull the
frame's side levers outwards (fig_a), rotate the
Ganciomatic hooks upwards, and then rotate the small
levers inwards (fig_b).
GANCIOMATIC FASTENING
27 Book Cross + Primo Viaggio SL
To mount the car seat on the stroller or chassis, you
must:
_ Engage the stroller's brake;
_ Lift the stroller's Ganciomatic hooks;
_ Pull the front bar out to the second position (fig_a).
_ Fully lower the backrest, if in place.
_ Place the car seat, facing mom, on the Ganciomatic
hooks and push it down until it clicks into place.
_ Once the seat is mounted, lift the backrest - if in place -
to the maximum height (fig_c).
_ See the instruction manual to release the car seat from
the stroller.
28 Book Cross + Navetta Pop-Up / Navetta XL / Navetta
Elite
To mount the Navetta Pop-Up / Navetta XL / Navetta
Elite on the chassis, you must:
_ Lock the stroller brakes;
_ Lift the Ganciomatic hooks;
_ Remove the front bar, if in place;
_ Position the Navetta Pop-Up / Navetta XL / Navetta
Elite, mum-facing, on the Ganciomatic hooks and push
it downwards, pressing on the sides, until you hear the
- 17 -