Pearson CE35-T Case страница 84 Скачать руководство пользователя

Страница: 84 / 144

HMI Display Screens

Alarm Description

The alarm description screen lists all the
alarms on the machine.

If there is an alarm present on the
machine, you cannot scroll through
this list; the cause of the active
alarm must be cleared before
continuing.

Use the directional keys to scroll
through the list of alarms.

The display in the top portion of the screen will include relevant
information, including possible causes of, or how to clear an alarm.

See the table below for a list of the alarm descriptions and the respective
information.

Alarm Descriptions

Main Drive Over current

Check for Obstruction in Flights.

Check Flight Drive Mechanical System

Flight Time Exceeded

Check PRS4.

Check Mechanical Drive System of Main Flights

Case Fail to Setup Alarm

Check Transfer of Blank.

Check Pickoff and Set up Vacuum System for Leaks.

Check PE6 and Air Supply.

Motor Protector Tripped

Reset Motor Protector In Electrical Enclosure.

Check Motor of Protector That Was Tripped.

Case at Seal Alarm

Check X-fer of Case to Seal.

Check Flap Plows.

Check Mechanical Setup at Tape Head.

Check PE7

Kickout Clutch Released

Check Prs6.

Check For Obstruction in Flights

Jog Flights to Reset

Tape Failed To Cut

Check Prs5

Check For Proper Tape Installation And Routing

Tape Failed To Apply

Check Prs5

Check For Proper Tape Installation And Routing

Press Main Screen to return to the main screen.

CE35-T Case Erector

Operations Manual

3/2/2010

M-CE35T-2c Horiz Mag

a
M-

a
m

)I
M

Fig. 64: Alarm Description Screen

Содержание CE35-T Case

















































































































































Результаты поиска

Содержание CE35-T Case

Отзывы:

Похожие инструкции для CE35-T Case

Бренды по названию

Популярные бренды

Pearson CE35-T Case, Руководство по эксплуатации

Результаты поиска

Содержание CE35-T Case

Отзывы:

Похожие инструкции для CE35-T Case

Бренды по названию

Популярные бренды