A
B
Drum Key
Initial Setting
Initial Setting
Heel Plate
Hinge
Footboard
Hinge
Flat Head
Screw
3-Piece Screw
Hinge
3-Piece Screw
Bottom Plate
Fig.9
Duo-Deck Footboard
The P-3002C features Pearl's patented Duo-Deck
Footboard, the world's first convertible Short / Long
Footboard.
To convert the Duo-Deck to a Long Footboard,
turn the pedal over and remove the four Flat Head
Screws with the provided Multi-Function Drum Key
or Allen wrench (3mm) as shown and remove the
Heel Plate and the Hinge from the Bottom Plate
(Fig.9).
Lift the Footboard and remove the four 3-Piece
Screws with the provided Multi-Function Drum Key
or Allen wrench (3mm) as shown, and remove
the Hinge from the Footboard (Fig.10).
Reattach the Hinge to the Footboard in the
position shown with two 3-Piece Screws using the
provided Multi-Function Drum Key or Allen wrench
(3mm) (Fig.11).
Short Footboard
Long Footboard
Fig.10
Fig.11
Index Mark
Index Mark
Beater Holder Link
Key Bolt
Uni-Lock Footboard
Angle Cam
Key Bolt
Beater Setting Stopper
Control Core Beater
Key Bolt
Drum Key
Beater Setting Stopper
Allen Screw
Beater Holder Link
Drum Key
Fig.2
Fig.1-B
Fig.1-A
Fig.3
Fig.4-A
Fig.8-A
Control Core Beater Setting
Insert the Control Core Beater into the Beater
Holder Link until it stops against the Beater Setting
Stopper, and tighten the Key Bolt with the provided
Multi Function Drum Key (Fig.1-A). Make sure that
the Beater Setting Stopper is flush against the
Beater Holder Link with the flat face square against
the Notch (Fig.1-B).
To change to a higher or shorter beater height,
loosen the Allen Screw on the Beater Setting
Stopper with the provided Multi-Function Drum Key
or Allen wench (3mm) then loosen the Key Bolt on
the Beater Holder Link (Fig. 3). Set the beater to
the desired height and re-tighten the Key Bolt.
Reset the Beater Setting Stopper flush against the
Beater Holder Link per the instructions above.
Footboard Angle Adjustment
The Footboard Angle can be adjusted by
loosening the Key Bolt on the Uni-Lock Footboard
Angle Cam and adjusting it to the desired angle
(Fig.8-A). Re-tighten the Key Bolt to secure the
angle. A gauge on the side of the Angle Cam is
provided to reference Footboard Angle settings
(Fig.8-B).
Beater Stroke Adjustment
The P-3002C Demon Chain Double Pedal features
Pearl's patented two-position Beater Holder that
can be positioned closer or farther from the drum
head for Finesse "A" Position setting or Power "B"
Position setting respectively.
It also rotates infinitely for perfect beater angle
without changing the footboard angle.
Changing the Beater Holder Position
To change to the Power setting, loosen the Key
Bolt to open the clamp and slide the Beater
Holder to the Power setting position (Fig.4-A, 4-B).
There is no need to remove the Key Bolt from the
clamp.
Beater Angle Adjustment
To change the angle of the Beater, loosen the Key
Bolt and set the angle to your preference and
re-tighten the Key Bolt (Fig.5).
Fig.4-B
"B" Position (Power)
"A" Position (Finesse)
Fig.8-B
Fig.5
Fig.6
Fig.7
Beater Holder Link
Tip
In the initial factory
setting, the Index Mark is
centered in the Window as
shown (Fig. 2)
Tip
If the Beater is too far
from the Bass Drum Head,
the Footboard can touch
the Hoop Clamp and
cause damage to the
Footboard and/or the
Hoop Clamp. To prevent
damage, please refer to
(Fig.7), and adjust the
Beater angle as shown.
Tip
Indicator marks are provided for referencing Beater
angle settings (Fig.6).
Tip
The Duo-Deck is set at the factory in the Short
Footboard setting.
Tip
The Beater Setting Stopper preserves the height
setting if the beater is removed when transporting the
pedal.
Tip
The Beater Holder is set at the factory in the Finesse
"A" Position.
