background image

PCAN-Router Pro FD – User Manual 
 

19 

Termination at Switch Position 

Type of Transceiver and 
Transmission Standard  

Off 

On 

High-speed CAN (ISO 11898-2) 

Transceiver installed by default. 

none 

120 

Ω

 between 

CAN_L and CAN_H 

Low-speed CAN (ISO 11898-3) 

Transceiver on request. 

4.7 k

Ω

 for 

CAN_L and CAN_H 

1.1 k

Ω

 for  

CAN_L and CAN_H 

Single-wire CAN (SAE J2411) 

Transceiver on request. 

9.1 k

Ω

 for CAN_SW 

2.1 k

Ω

 for CAN_SW 

 

Attention!

 Electrostatic discharge (ESD) can damage or destroy 

components on the card. Take precautions to avoid ESD. 

Do the following to activate the CAN termination: 

1.

 

Disconnect the device from the power supply. 

2.

 

Remove the two upper screws on the front and rear of the 
housing. 

3.

 

Pull the housing cover upwards. 

4.

 

Use a slotted screwdriver and set the switch of the desired 
CAN channel from 

off

 to 

on

5.

 

Put the housing cover back in place. 

6.

 

Fasten the four screws to the front and rear of the housing. 

4.3

 

Changing the Button Cell for the Real-
Time Clock (RTC) 

The real-time clock (RTC) installed in the PCAN-Router Pro FD is 
supplied by a button cell of the IEC type CR1620 (3 V) as long as the 
device is switched off (without power supply). 

Содержание IPEH-002220

































































Отзывы: