background image

Page 5

Warranties and Liabilities

Warranty & Liability Coverage

1.  Peak warrants that, subject to the provisions in this statement, purchased Peak generators, whether 

purchased directly from Peak or indirectly via an approved, certified and trained distributor or partner 

(referred to hereafter as a “Peak Partner”) will comply in all material respects with any specifications 

referred to in your customer order confirmation and, subject to installation and operational guidelines 

being followed as described in applicable product manuals, shall be free from any defects in quality 

of materials or workmanship for a period of one year from the date of installation, provided this takes 
place within 3 months of factory dispatch.

2.  Where the purchased generator is from the Precision Hydrogen series, Peak further warrants that, 

subject to installation and operational guidelines being followed as described in applicable product 

manuals, the hydrogen cell shall be free from any defects in quality of materials or workmanship for a 

total period of three years (inclusive of warranty period specified in clause 1) from date of installation, 
provided this takes place within 3 months of factory dispatch.

3.  Where the purchased generator is from the i-Flow 6000 series, Peak further warrants that, subject 

to installation and operational guidelines being followed as described in applicable product manuals, 

the generator shall be free from any defects in quality of materials or workmanship for a total period 

of two years (inclusive of warranty period specified in clause 1) from the date of installation, provided 

this takes place within 3 months of factory dispatch and the following provisions have also been met:                

a. you must purchase a service plan, ensuring the generator is serviced by Peak or a Peak Partner on 

or before the end of the first 12 months of your ownership, and serviced at least once during each 

subsequent 12 month period thereafter;               b. the generator (and any associated equipment) 

must have been commissioned by Peak or a Peak Partner; 

c. the feed air or inlet air supply to the generator must comply with ISO 8573-1:2010 Class 1.2.1 at all 

times; 

d. your air compressor, dryer, filtration and oil removal systems must be deemed suitable for use 

by Peak or a Peak Partner, and must be changed and serviced regularly, in line with the equipment 

manufacturer’s recommended guidelines; and 

e. any generator failure or fault that is deemed to have been caused by the failure of any upstream 

equipment, component, part or system (such as air compressor, air treatment or filtration) will be 
excluded from the warranty described herein.

4.  Peak also warrants that any replacement parts whether purchased (directly from Peak, or via a Peak 

Partner) or supplied as part of any remedial action undertaken in line with the provisions of clauses 12 

and 13, shall be free from any defects in quality of materials or workmanship for a period of 180 days 
from the date of factory dispatch, provided its installation is performed by Peak or a Peak Partner.

5.  This warranty does not exclude Peak’s liability in respect of any claim for death or personal injury 

to any person, in so far as such can be attributed to negligence or breach of duty of care directly 

resulting from failure of Peak to comply with the provisions in clauses 1, 2, 3 & 4. 

 

Exclusions & Limitations

6.  This warranty does not cover: 

a. damage, deterioration or malfunction resulting from an alteration or modification to a generator 

which has not been carried out by Peak or a Peak Partner; 

b. damage, deterioration or malfunction resulting from what Peak reasonably believes to be abuse, or 

misuse of a generator by you or any third party; 

c. liability for accident or neglect (other than pursuant to clause 5); 

d. maintenance or repairs which have not been carried out by Peak or a Peak Partner; 

e. operation of a generator or exposure of a generator to environmental conditions that fall out-with 

operational guidelines as specified in the applicable product user manual; and 

f. lightning, power surges or any other acts of God or nature.

7.  This warranty is non-transferrable. Only the original owner of the generator may benefit from the 

terms within this statement. 

8.  Peak shall not be liable in respect of any claim made for costs, damages, losses or expenses (whether 

Содержание Genius N118LA



























Отзывы: