3. Reader Connection
2. Mounting Controller
6. Locking Relay
5. Input B / REX Connection
4. Input A / DPS Connection
1. Package Contents
Jumpers (4)
Diodes (2)
Battery Leads (1)
Nuts (4)
Red Pedestal Controller (1)
Bolts (4)
Mount
-
Mount the Red Pedestal enclosure securely.
+ -
0 1 L
+ -
0 1 L
A
-
B
A
-
B
NC NO
C
NC NO
C
12VDC
+ GND
OSDP
OSDP
PORT1
BUS
+
-
PORT2
BUS
+
-
ETHERNET
POWER
HEART
LINK
ACTIVITY
BATTERY
POE IN
POE OUT
OSDP
Wiring
D
+ -
0 1 L
+ -
0 1 L
A
-
B
A
-
B
NC NO
C
NC NO
C
12VDC
+ GND
OSDP
OSDP
PORT1
BUS
+
-
PORT2
BUS
+
-
BATTERY
B
C
A
Reader
+ -
0 1 L
A
Main Reader
-
The main reader is mounted at the door with a 22/5 or 22/6
wire ran to the door controller. Wire the reader to the controller as shown
above. Be sure to check polarity and voltage prior to powering the controller.
B
Secondary Reader
-
Wire the second reader to the controller as shown
above. Be sure to check polarity and voltage prior to powering the controller.
D
Piezo
-
Can be connected to available relay and configured with software
C
OSDP
-
Place jumper(s) to enable OSDP (see OSDP reference guide at the
end of this guide for more info)
Red Pedestal Controller
+ -
0 1 L
+ -
0 1 L
A
-
B
A
-
B
NC NO
C
NC NO
C
12VDC
+ GND
OSDP
OSDP
PORT1
BUS
+
-
PORT2
BUS
+
-
ETHERNET
POWER
HEART
LINK
ACTIVITY
BATTERY
POE IN
POE OUT
Double DPS
Contact
A
+ -
0 1 L
+ -
0 1 L
A
-
B
A
-
B
NC NO
C
NC NO
C
12VDC
+ GND
OSDP
OSDP
PORT1
BUS
+
-
PORT2
BUS
+
-
BATTERY
DPS (Door Position Switch)
- The DPS is mounted on the door frame in the
desired location with a 22/2 wire running from the DPS to the
controller
.
Wire the DPS to the
controller
as shown above. When using two DPS
sensors for double doors, you will wire them in series with only two
conductors running back to the controller for connection.
AUX Input
- A rule can be set up to trigger events or outputs based on this
input trigger.
B
DPS Contact
A
B
+ -
0 1 L
+ -
0 1 L
A
-
B
A
-
B
NC NO
C
NC NO
C
12VDC
+ GND
OSDP
OSDP
PORT1
BUS
+
-
PORT2
BUS
+
-
BATTERY
If using a powered REX,
run to any 12VDC
output on controller.
B
A
Maglock
REX
C
PORT1
BUS
+
-
Maglock
- When installing a Maglock, it is typical to install a REX (Request
to Exit) at the door for free egress. Run an 18/2 wire from the Maglock to
the
door controller
, connecting to the Maglock as shown.
REX (Request to Exit)
- The REX is mounted in the desired location with an
18/5 wire ran from the REX to the controller. Wire the REX to the
controller
and Maglock, as shown above. If reporting is not needed in the system,
simply eliminate the green-labeled wire.
A
B
Jumper
- Use the designated jumper(s) to energize the relay output NO and
NC to utilize the output as a wet contact.
C
Gate Operator
- Follow the gate operator wiring instructions to connect the
gate operator to an ELK 912B Isolation Relay.
Isolation Relay
- Installation of an ELK 912B Isolation relay is recommended
to prevent electrical damage to the Red Gate, Isolation relay is
sold separately.
Locking Relay
- Connect the ELK 912B Isolation relay to the Red Pedestal
by connecting the positive wire into a positive port and the negative wire
into the NO port on the board.
Jumper
- Use the designated jumper(s) to energize the relay output to be
NO by placing the jumper on the negative (-) and center pins.
+ -
0 1 L
+ -
0 1 L
A
-
B
A
-
B
NC NO
C
NC NO
C
12VDC
+ GND
OSDP
OSDP
PORT1
BUS
+
-
PORT2
BUS
+
-
BATTERY
C
A
D
B
NO
NO
COM
D2
Wiring from Gate Operator
-
+
PORT1
BUS
+
-
ELK 912B
Isolation Relay
(sold separately)
A
B
C
D
