background image

Model Number

130A 25

ICP® ELECTRET ARRAY MICROPHONE

Revision: NR
ECN #: 50628

P erfo rm an ce

EN G L ISH

SI

Nominal Microphone Diameter

1/4"

1/4"

Frequency Response Characteristic(at 0°
incidence)

Free-Field

Free-Field

Frequency Response(± 2 dB)

20 to 10,000 Hz

20 to 10,000 Hz

Frequency Response

(± 3 dB)

10 to 16,000 Hz

10 to 16,000 Hz

Frequency Response

(± 4 dB)

10 to 20,000 Hz

10 to 20,000 Hz

Phase Match(100 Hz to 3 kHz)

± 3 °

± 3 °

[1]

Phase Match

(50 Hz to 5 kHz)

± 5 °

± 5 °

[1]

Phase Match

(5 kHz to 10 kHz)

± 10 °

± 10 °

[1]

Sensitivity

45 mV/Pa

45 mV/Pa

Sensitivity

(+/- 3)(@ 250 Hz)

-26.9 dB re 1 V/Pa

-26.9 dB re 1 V/Pa

Inherent Noise(Linear)

29 dB re 20 µPa

29 dB re 20 µPa

[1]

Inherent Noise

(A Weighted)

< 26 dB(A) re 20 µPa

< 26 dB(A) re 20 µPa

Inherent Noise

(A Weighted)

24 dB(A) re 20 µPa

24 dB(A) re 20 µPa

[1]

Dynamic Range(3% Distortion Limit)

122 dB re 20 µPa

122 dB re 20 µPa

[1]

TEDS Compliant

Yes

Yes

[2]

En viro n m en tal

Temperature Range(Operating)

+14 to +122 °F

-10 to +50 °C

Temperature Effect on Output(-10 to +50
°C)

0.7 dB

0.7 dB

[1]

Electrical

Excitation Voltage

18 to 30 VDC

18 to 30 VDC

Constant Current Excitation

2 to 20 mA

2 to 20 mA

Output Bias Voltage

5.5 to 14 VDC

5.5 to 14 VDC

Output Impedance

< 150 Ohm

< 150 Ohm

P h ysical

Housing Material

Stainless Steel

Stainless Steel

Electrical Connector(Output)

10-32

10-32

Size (Diameter x Length)(overall)

0.28 in x 1.35 in

7.0 mm x 34.4 mm

Weight

0.19 oz

5.3 gm

[1]

[3]

All specifications are at room temperature unless otherwise specified.
In the interest of constant product improvement, we reserve the right to change specifications without notice.

ICP

®

 is a registered trademark of PCB Piezotronics, Inc.

OP TION A L  VERSION S

Optional versions have identical specifications and accessories as listed for the standard model except

where noted below. More than one option may be used.

N OTES:

[1]Typical.
[2]TEDS Capable Digital Communication, compliant with IEEE 1451.4
[3]See PCB Declaration of Conformance PS023 for details.

Date: 03/24/2020

Date: 03/24/2020

Date: 03/24/2020

Date: 03/24/2020

72403

Entered: LK

Engineer: MJN

Sales: MV

Approved: NJF

Spec Number:

3425 Walden Avenue, Depew, NY 14043

Phone: 716-684-0001
Fax: 716-684-0987
E-Mail: [email protected]

Содержание 130A25
















Отзывы: