PC Partner 35892900 Series Скачать руководство пользователя страница 1

1

Electronic Emission Notices

Federal Communications Commission (FCC) Statement

This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with instructions
contained in this manual, may cause harmful interference to radio and
television communications. However, there is no guarantee that interference
will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:

-

REORIENT OR RELOCATE THE RECEIVING ANTENNA

-

INCREASE THE SEPARATION BETWEEN THE EQUIPMENT AND THE RECEIVER

-

CONNECT THE EQUIPMENT INTO AN OUTLET ON A CIRCUIT DIFFERENT FROM
THAT OF THE RECEIVER

-

CONSULT THE DEALER OR AN EXPERIENCED AUDIO/TELEVISION TECHNICIAN

NOTE: Connecting this device to peripheral devices that do not comply with

Class B requirements, or using an unshielded peripheral data cable,
could also result in harmful interference to radio or television reception.

The user is cautioned that any changes or modifications not expressly
approved by the party responsible for compliance could void the user’s
authority to operate this equipment.

To ensure that the use of this product does not contribute to interference,
it is necessary to use shielded I/O cables.

Copyright

This manual is copyrighted with all rights reserved. No portion of this manual may be
copied or reproduced by any means.

While every precaution has been taken in the preparation of this manual, no responsibility
for errors or omissions is assumed. Neither is any liability assumed for damages resulting
from the use of the information contained herein.

Trademarks

All brand names, logos and registered trademarks mentioned are property of their
respective owners.

Содержание 35892900 Series

















Отзывы: