manualshive.com logo in svg

PAW FC3.10, Инструкции по сборке, установке и эксплуатации, Страница: 62 / 80

Поделиться
Скачать
PAW FC3.10 Скачать руководство пользователя страница 62

 

 

23 Connection to Building Management System 

62 

99E13331xx-mub-en - V08 

2022/07 

23

 

Connection to Building Management System 

The connection to the Building Management System (BMS) can be realised for an individual 
domestic hot water module as well as for cascade operation (up to 4 single modules). The BMS 
connection is carried out via the Modbus interface of the controller (single domestic hot water 
module) or the Modbus RTU module MB3.10 (in the following abbreviated MB3.10) for Friwa 
Cascade. For the data exchange between the participants of the bus, the Modbus RTU protocol 
is used. 

23.1

 

Single domestic hot water module 

Connection of the controller to BMS 
The domestic hot water modules with the FC3.10 controller have the great advantage that the 
Modbus interface already exists at the controller. No additional hardware is required to realise 
the BMS connection. Please use the PAW original communication cable RJ10 (item no. 
N00317) to connect the FC3.10 controller to the BMS.  
Insert one plug of the cable into the RS-485 port of the FC3.10 controller.  
Use the other plug for the BMS connection.  

 

 
 
 
 
 
 
 
 

If the connection to the BMS is 
meant to be realised via a 
clamping connection, please 
consider the pin assignment of the 
communication cable. 

Содержание FC3.10

















































































Отзывы:

Нет отзывов