EN
166
EN
167
Care & Maintenance
Replacement Parts
Warning!
Replacement parts must
conform with the requirements
specified by the manufacturer. Therefore
use original replacement parts only or
spare parts authorised by the manufactur-
er.
In case of service requests or spare parts,
please contact your local HORNBACH store or
write an email to: [email protected]
Caution!
Before performing any
work on the tool, remove the battery.
Clean the cutter bar after each use:
- Remove contamination, remains of blades
etc.
- Place the hedge trimmer on its side and ap-
ply a thin film of oil to the cutter bar. Prefer-
ably use environmentally friendly lubricants,
e.g. service sprays.
Caution!
Wear protective gloves
when handling the cutting bar!
Caution!
Do not oil the hedge trim-
mer while it is running.
- Clean the unit after every use. Failure to
clean the unit can damage the materials
and cause malfunctions.
- Remove dirt and dust from the tool with a
paint brush or dry cloth.
- Place the cutting device cover on the cut-
ter bar.
- Never spray the hedge trimmer with water.
- Keep the ventilation slots clean and free of
dust.
- Keep the tool, in particular its plastic com-
ponents, away from brake fluids, petrol,
petroleum products, penetrating oil, etc.
These substances may lead to damage.
- Do not store the tool near fertilisers and
other garden chemicals. Danger of corro-
sion.
- Store the battery and the appliance sepa-
rately.
- Charge the battery before storing the appli-
ance in winter.
- Store the appliance in a dry and frost-free
place (10-25 °C).
- Repairs may be carried out by an authorised
customer service only.
Residual risks
Even if you are operating this product in
accordance with all the safety require-
ments, potential risks of injury and dam-
age remain. The following dangers can
arise in connection with the structure and
design of this product:
1. Injuries and damage to property due to
broken application tools.
2. Danger of injury and property damage
caused by flying objects.
Technical Data
CORDLESS POLE HEDGE TRIMMER
PE-AHH 20 Li
Nominal voltage
20 V
No-load speed (n
0
)
2200/min
Cutting length
450 mm
Maximum branch thickness
16 mm
Weight
3.58 kg
Sound pressure level (L
pA
)
75 dB(A) / Uncertainty K = 3 dB(A)
Measured sound power level (L
WA
)
87 dB(A) / Uncertainty K = 2.58 dB(A)
Max. vibration emission (a
hw
)
≤ 2.5 m/s² / Uncertainty K = 1.5 m/s²
SUITABLE BATTERIES
PE-AK2, PE-AK4 (not included)
Voltage
20 V
Capacity
PE-AK2 (6801240): 2.0 Ah Li-ion battery
PE-AK4 (6801241): 4.0 Ah Li-ion battery
Operating temperature
10-40 °C
Storage temperature
10-25 °C
SUITABLE CHARGER
PE1H (not included)
Nominal voltage
100-240 V ~ 50/60 Hz, 78 W
Output voltage
14.4-20 V , 3.0 A
Charging time
60 min for PE-AK2
120 min for PE-AK4
Operation temperature
10-40 °C
Protection Class
/ II
Weight
0.25 kg
The declared vibration total value and the
declared noise emission values have been
measured in accordance with a standard test
method (EN 62841) and may be used for com-
paring one tool with another. The declared
vibration total value may also be used in a
preliminary assessment of exposure.
Caution!
The vibration and noise emis-
sion during actual use of the power tool
can differ from the declared total value depend-
ing on the ways in which the tool is used, in par-
ticular, what kind of work piece is machined.
It is necessary to identify safety measures to
protect the operator that are based on an es-
timation of exposure in the actual conditions
of use (taking account of all parts of the op-
erating cycle such as the times when the tool
is switched off and when it is running idle in
addition to the trigger time)
Try to minimize the impact of vibration and
noise. Exemplary measures to reduce vibra-
tion exposure include wearing gloves while
using the tool, limiting working time, and us-
ing accessories in good condition.
Noise & Vibration
