-23 -
PATON
MultiPRO
DC MMA/TIG/MIG/MAG
a) [2T] - 2T torch button mode
b) [4T] - 4T torch standard button mode
c) [alt.4T] - 4T torch alternative button mode
2) [Ind] inductance = OFF (by default)
а) 0 [OFF] ... Stage
6 (change step 1 stage)
3) [t.Pr] shielding gas pre-purge time = 0.1 sec (by default)
a) 0.1 ... 25.0 sec (change step 0.1 sec)
4) [t.P0] shielding gas post-purge time = 1.5 sec (by default)
a) 0.1 ... 25.0 sec (change step 0.1 sec)
5) [t.up] voltage build-up time = OFF (by default)
a) 0 [OFF] ... 5.0 sec (change step 0.1 sec)
6) [t.dn] voltage ramp-down time = 0.1 sec (by default)
a) 0.1 ... 5.0 sec (change step 0.1 sec)
7) [Po.P] voltage pulsation mode = OFF (by default)
a) ON
–
enabled
b) OFF
–
disabled
8) [u.iP] pulse voltage = 19V (by default)
a) 12 ... 28.0V (change step 0.1V ) for MultiPRO-250
b) 12 ... 29.0V (change step 0.1V ) for MultiPRO-270
c) 12 ... 30.0V (change step 0.1V ) for MultiPRO-350
9) [u.PS] pause voltage = 19V (by default)
a) 12 ... 28.0V (change step 0.1V ) for MultiPRO-250
b) 12 ... 29.0V (change step 0.1V ) for MultiPRO-270
c) 12 ... 30.0V (change step 0.1V ) for MultiPRO-350
10) [Fr.P] voltage pulsation frequency = 20Hz (by default)
a) 5 ... 500 Hz (step change 1 Hz)
11) [dut] pulse rate (duty cycle)
–
it is the percentage of the voltage pulse to the period of repetition of these pulses = 7% (by default)
a) 2 ... 20% (change step 1%)
Right indicator of the wire feeder:
0) [-1-] main displayed parameter FEED SPEED = 7.0 m/min (by default)
a) 2.0 ... 16.0 m/min (change step 0.1 m / min)
1) [But] torch button mode = [2T] (by default)
a) [2T] - 2T torch button mode
b) [4T] - 4T torch standard button mode
c) [alt.4T] - 4T torch alternative button mode
2) [Dru] wire feed motor ON/OFF = ON (by default)
a) ON - enabled (if there is a connection, the unit turns on automatically in the MIG/MAG mode)
b) OFF - disabled (if there is a connection, the unit turns off automatically in the MMA and TIG mode)
3) [t.Pr] shielding gas pre-purge time = 0.1 sec (by default)
a) 0.1 ... 25.0 sec (change step 0.1 sec)
4) [t.P0] shielding gas post-purge time = 1.5 sec (by default)
a) 0.1 ... 25.0 sec (change step 0.1 sec)
5) [t.uP] wire feed speed build-up time = 0.1 sec (by default)
a) 0 [OFF] ... 5.0 sec (change step 0.1 sec)
6) [t.dn] wire feed speed ramp-down time = OFF (by default)
a) 0 [OFF] ... 5.0 sec (change step 0.1 sec)
