Pasco Scientific OS-8523 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 22

Pasco Scientific OS-8523 Скачать руководство пользователя страница 14

Slit Accessory

012-05880B

10

While the interference fringes are created by the interference of the light coming from the two
slits, there is also a diffraction effect occurring at each slit due to Single Slit diffraction. This
causes the envelope as seen in Figure 2.2.

Setup

➀

Set up the laser at one end of the optics bench and place the Multiple Slit Disk in its holder about
3 cm in front of the laser. See Figure 2.3.

➁

Cover the screen with a sheet of paper and attach it to the other end of the bench so that the paper
faces the laser.

➂

Select the double slit with 0.04 mm slit width and 0.25 mm slit separation by rotating the slit disk
until the desired double slit is centered in the slit holder. Adjust the position of the laser beam
from left-to-right and up-and-down until the beam is centered on the double slit.

Procedure

➀

Determine the distance from the slits to the screen.

Note that the slits are actually offset from the center line of the slit holder. Record the screen
position, slit position, and the difference between these (the slit-to-screen distance) in Table 2.1.

➁

Turn off the room lights and mark the positions of the maxima in the interference pattern on the
screen.

➂

Turn on the room lights and measure the distance between the first order (m = 1) marks and
record this distance in Table 2.1. Also measure the distance between the second order (m = 2)
marks and record in Table 2.1.

Table 2.1: Data and Results for the 0.04 mm/0.25 mm Double Slit

laser

screen

slit

Figure 2.3: Optics Bench Setup

Slit-to-screen distance (D) = _________________

First Order (m = 1)

Second Order (m = 2)

Distance between

side orders

Distance from center

to side (y)

Calculated slit

separation

% difference

«
...
12
13
14
15
16
...
»

Содержание OS-8523























Отзывы:

Нет отзывов