background image

 

User Manual, MAR-5915-2x 
User Manual 

 

Chapter 3  Connector and LED 

Descriptions  

 

MNL-0655-01  Rev A6   

ECO-5592 

Effective: 05 Feb 19   

 

Page 25 of 40

  

 

 

J2 ETH 0 Pinouts 

J2 provides the signals for the Ethernet ports in the ROU ring.  The ROU has five Ethernet ports, four of 
which are on J2.  

 

 

Figure 8.  Connector J2 ETH 0 

Connector Alignment:  facing the insert side of the 
connector (pin side).  The connector on the DuraMAR 
5915-2x front panel (socket side) appears as an exact 
mirror of the picture on the left. 

 

P/N: D38999/20FC35SN 

(Shell Size 13) 

 

5915-2x Ethernet Connector Pinout 

The ROU ring provides two switched and two routed ports to the outside.  Ports 0 and 1 are the routed 
ports; ports 2 and 3 are the switched ports. 

Note:

 Port 4 is internally connected to SWI port FE18. 

 

J2 Signal Name 

Description 

38999 Pin # 

ETH 0_P 

10/100 TX 0 + 

ETH 0_PORT0_TX- 

10/100 TX 0 - 

ETH 0_P 

10/100 RX 0 + 

ETH 0_PORT0_RX- 

10/100 RX 0 - 

ETH 0_PORT1_TX- 

10/100 TX 1 - 

ETH 0_P 

10/100 TX 1 + 

17 

ETH 0_P 

10/100 RX 1 + 

ETH 0_PORT1_RX- 

10/100 RX 1 - 

ETH 0_PORT2_TX- 

10/100 TX 2 - 

ETH 0_P 

10/100 TX 2 + 

ETH 0_P 

10/100 RX 2 + 

10 

ETH 0_PORT2_RX- 

10/100 RX 2 - 

19 

ETH 0_PORT3_TX- 

10/100 TX 3 - 

11 

ETH 0_P 

10/100 TX 3 + 

12 

ETH 0_P 

10/100 RX 3 + 

13 

ETH 0_PORT3_RX- 

10/100 RX 3 - 

14 

.nc. 

Reserved 

15 

.nc. 

Reserved 

16 

Содержание DuraMAR 5915-2X









































Отзывы: