Parksafe Automotive SW004SSD Скачать руководство пользователя

Страница: 17 / 82

Different beeping modes stand for different working status as below:

a. The electronic lock is open: one long beep and one short beep

b. No disk: one long beep and two short beeps

Abnormal disk system: one long beep and three short beeps

d. If the disk is well connected but the alarm video files are full : two short beeps and one

short beep

e. No camera input: two short beeps , and two short beeps after a second

If the disk is well connected but the device is not in recording: two short beeps and three

short beeps

6.5 Recording Files Output

Connect the3 PIN female of cable ”SSD OUT” to the 3 PIN male on the device

Connect

the device to a computer by USB

A computer could be connected to the device and read the SSD through the SSD-out cable, which
enables the users to read the disk without taking it out .

6.5 Alarm Interface



Alarm interface cable

See the picture below

Содержание SW004SSD



















































































Результаты поиска

Содержание SW004SSD

Отзывы:

Похожие инструкции для SW004SSD

Бренды по названию

Популярные бренды

Parksafe Automotive SW004SSD, Руководство по эксплуатации

Результаты поиска

Содержание SW004SSD

Отзывы:

Похожие инструкции для SW004SSD

Бренды по названию

Популярные бренды