background image

 

Cont.2

 

 

 

FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS 

DESCRIBED HEREIN OR RELATED ITEMS CAN CAUSE DEATH, PERSONAL 

INJURY AND PROPERTY DAMAGE. 

This document and other information from Parker-Hannifin 

Corporation, its subsidiaries and authorized distributors 

provide product or system options for further investigation by 

users having technical expertise. 

The user, through its own analysis and testing, is solely 

responsible for making the final selection of the system and 

components and assuring that all performance, endurance, 

maintenance, safety and warning requirements of the 

application are met. The user must analyze all aspects of the 

application, follow applicable industry standards, and follow 

the information concerning the product in the current product 

catalog and in any other materials provided from Parker or its 

subsidiaries or authorized distributors. 

To the extent that Parker or its subsidiaries or authorized 

distributors provide component or system options based upon 

data or specifications provided by the user, the user is 

responsible for determining that such data and specifications 

are suitable and sufficient for all applications and reasonably 

foreseeable uses of the components or systems. 

 

Содержание Siemens APOGEE P1





















Отзывы: