Parker PSD1 Скачать руководство пользователя страница 54

Страница: 54 / 109

Installation of the multi-axis system PSD1-M

54 (109)

192-011006N8 2019-07

09.10.19 09:27

For EX motors, EY motors, NK motors, NV motors and NX motors:

Designation Axis

Motor cable lead
designation*

Motor side
EX, EY, NK, NV, NX

U / L1

V / L2

W / L3

FE & PE

YE / GN

5.9

Motor feedback

Feedback system can be destroyed if configured incorrectly!

If you connect a PSD that has already been configured for a specific feedback

system to another feedback system, it can be destroyed by too high a voltage.

Procedure when changing the feedback system.

5.9.1.

X48: HIPERFACE DSL® & motor temperature sensor (PSD1-M)

HIPERFACE DSL® feedback and motor temperature sensor connection for 3

axes

The respective pins are not assigned with 1- or 2-axis devices!

Pin Designation

Axis

PTC+

Temperature motor 1

PTC-

Temperature sensor - motor 1

3 PTC+

Temperature motor 2

PTC-

Temperature sensor - motor 2

PTC+

Temperature motor 3

PTC-

Temperature sensor - motor 3

DSL+

DSL-

DSL+

10 DSL-

11 DSL+

12 DSL-

Connection on the device

(see page 46, see page 59, see page 30).

We recommend the operation with Parker

HIPERFACE DSL® cables!

(see page

82)

Note the following, if no Parker PSD DSL motor cable is used:

The internal shielding of the Hiperface DSL® signal line must be connected

(braided or soldered) to the outer motor cable shielding (and thus to PE). Up from

this connection point, the internal shielding of the Hiperface DSL® line must be

guided up to the Hiperface DSL® connection terminal of the PSD servo amplifier.

Содержание PSD1














































































































Результаты поиска

Содержание PSD1

Отзывы:

Parker PSD1, Руководство по установке, Страница: 54 / 109

Результаты поиска

Содержание PSD1

Отзывы: