Parker Helac PowerTilt PT-4.5 Скачать руководство пользователя

Страница: 10 / 12

Parker Hannifin Corporation

Helac/Cylinder Division

Enumclaw, Washington USA

www.helac.com

PowerTilt Tilting Coupler

PT-4.5 Service & Repair Manual

HY34-1370

Maintenance

Grease the thrust washers at the two grease

fittings with a high quality Lithium-based

grease. Apply grease until clean grease flows

from the grease reliefs. Severe operating
conditions such as abrasive dust or prolonged
submersion in water may require more
frequent grease applications.

Make sure the grease reliefs are functioning

properly. Open or replace non-functioning
grease reliefs immediately.

NOTICE

Never replace the grease relief

valves with grease fittings or

plugs.

NOTICE

Do not operate the PowerTilt if the

grease reliefs are not functioning.

Check shaft end play. When the end play

exceeds 0.38 mm, the end cap must be
tightened.

Retighten torque foot M10 bolts (114) to 68

Nm (50 ft-lbs) and tie rod bolt nut (411) to 920
Nm (680 ft-lbs)

Daily

Monthly

Maintenance

Содержание Helac PowerTilt PT-4.5













Результаты поиска

Содержание Helac PowerTilt PT-4.5

Отзывы:

Похожие инструкции для Helac PowerTilt PT-4.5

Бренды по названию

Популярные бренды

Parker Helac PowerTilt PT-4.5, Руководство по обслуживанию и ремонту

Результаты поиска

Содержание Helac PowerTilt PT-4.5

Отзывы:

Похожие инструкции для Helac PowerTilt PT-4.5

Бренды по названию

Популярные бренды