Parker Daedal 412LXR Series Скачать руководство пользователя | Manualshive

Страница: 7 / 47

background image

412LXR Series Product Manual

Chapter 1 - Introduction

7

Specification Conditions and Conversions

Specifications are Temperature Dependent
Catalog specifications are obtained and measured at 20 Degrees C. Specifications at any other
temperature may deviate from catalog specifications. Minimum to maximum continuous operating
temperature range (with NO guarantee of any specification except motion) of a standard unit before
failure is 5 - 40 Degrees C.

Specifications are Mounting Surface Dependent
Catalog specifications are obtained and measured when the positioner is fully supported, bolted down,
and is mounted to a work surface that has a maximum flatness error of 0.013mm/300mm (0.0005”/ft).

Specifications are Point of Measurement Dependent
Catalog specifications and specifications in this manual are measured from the center of the carriage, 38
mm above the carriage surface. All measurements taken at any other location may deviate from these
values.

«
...
5
6
7
8
9
...
»

Содержание Daedal 412LXR Series
















































Отзывы:

Нет отзывов

Похожие инструкции для Daedal 412LXR Series

Бренд: Samson Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды