manualshive.com logo in svg

Parker ACR7000 Series, Руководство пользователя

Поделиться
Скачать
Parker ACR7000 Series Скачать руководство пользователя страница 46

COMMUNICATIONS 

46   

ACR7000 Controller Installation Guide  

Ethernet Connector Pinout 

The following table contains the Ethernet connector pinout. 

RJ-45 Connector Pinout 

Signal 

Pin 

Wire Color 

Description 

RX+ 

1 

White with orange 

Differential Receive positive side 

RX- 

2 

Orange 

Differential Receive negative side 

TX+ 

3 

White with green 

Differential Transmit positive side 

4 

Blue 

Not used 

5 

White with blue 

Not used 

TX- 

6 

Green 

Differential Transmit negative side 

7 

White with brown 

Not used 

8 

Brown 

Not used 

Note: Pin assignment follows EIA/TIA T568B guidelines. 

 

RJ-45 LED Ethernet Status Indicators 

LEDs located on the RJ-45 socket connector indicate Ethernet status. The next table describes the LED states and 
their meanings. 

RJ-45 Ethernet Status LED Indications 

Signal 

Steady 

Flash 

Description 

Ethernet 
Link/Activity 

Off 

— 

No Ethernet link 
detected 

Yellow 

— 

Ethernet link established, 
no activity 

— 

Yellow 

Ethernet link established 
and active 

Ethernet 
Speed 

Off 

— 

Ethernet 10Mbps 

Green 

— 

Ethernet 100Mbps 

 

 

Содержание ACR7000 Series






























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды