Paramount Fitness ME II Скачать руководство пользователя

Страница: 148 / 195

Paramount User Guide

148

P a g e

corrections. This data is saved to the control system's Flash RAM, and will be always be used
to correct the mount's periodic error (provided the

Apply PEC Corrections

checkbox is turned

on).

Step 3

Save the PEC Curve to the Paramount Firmware

Click the

Save

button to save this curve into the Paramount's PEC table (that is, the curve is

saved in the control system's flash RAM for permanent use).

Step 4

Apply PEC Corrections

From

TheSkyX Professional Edition

, connect to the Paramount by clicking the

Connect

command on the

Telescope

menu.

Open the

Bisque TCS

window (see page 120).

Click the

Periodic Error Correction

tab.

Turn on the

Apply PEC Corrections

checkbox.

Your Paramount will now use the optimal PEC curve for the errors in your worm/gear.

Utilities Tab

The Utilities tab provides access to many high-level control system settings.

Hemisphere Setup

Click the

Hemisphere Setup

text on the right side of the

Utilities

tab to configure the mount’s tracking

direction and show hemisphere-specific mount status. (The home sensor values are shown only when the
mount is connected.)

Figure 80: Example hemisphere settings for the northern hemisphere.

Содержание ME II



































































































































































































Результаты поиска

Содержание ME II

Отзывы:

Похожие инструкции для ME II

Бренды по названию

Популярные бренды

Paramount Fitness ME II, Руководство пользователя

Результаты поиска

Содержание ME II

Отзывы:

Похожие инструкции для ME II

Бренды по названию

Популярные бренды