background image

 1

8776-A2-GZ40-40

February 2001

Hotwire

r

 8776 TDM SDSL Termination Unit 

with G.703 Interface
Installation Instructions

Document Number 8776-A2-GZ40-40

February 2001

Product Documentation Online

Complete documentation for this product is available at www.paradyne.com.
Select Library 

 Technical Manuals 

 Hotwire DSL & MVL Systems.

Select the following document:

8776-A2-GB20
Hotwire 8776 TDM SDSL Termination Unit, with G.703 Interface, User’s
Guide

To order a paper copy of a Paradyne document:

H

Within the U.S.A., call 1-800-PARADYNE (1-800-727-2396)

H

Outside the U.S.A., call 1-727-530-8623

Hotwire 8776 TDM SDSL Termination Unit

The Hotwire

r

 8776 Termination Unit is a circuit card assembly that contains four

Time Division Multiplexer Symmetric Digital Subscriber Line (TDM SDSL) ports
and a G.703 interface. When the unit is used in a Hotwire 8600 or 8800 Series
Digital Subscriber Line Access Multiplexer (DSLAM) chassis, it transports up to
2048 kbps signals over traditional twisted-pair telephone wiring.

!

HANDLING PRECAUTIONS FOR
STATIC-SENSITIVE DEVICES

This product is designed to protect sensitive components from damage
due to electrostatic discharge (ESD) during normal operation. When
performing installation procedures, however, take proper static control
precautions to prevent damage to equipment. If you are not sure of the
proper static control precautions, contact your nearest sales or service
representative.

496-15104

Содержание Hotwire 8776





















Отзывы: