Paradyne COMSPHERE 6800 Series Скачать руководство пользователя | Manualshive

Страница: 85 / 237

background image

COMSPHERE 6800 Series Network Management System

2-62

January 1997

6800-A2-GB31-20

Add to active list

Enter the name(s) or network address(es) of the device(s) to be placed on the specified
device’s poll list as actively polled devices.

Add to skipped list

Enter the name(s) or network address(es) of devices to be skipped during device polling.
Devices will remain on the poll list but will not be polled.

Set CCN event (Required field)

If configuration change notification has been enabled for this modem, use this field to
determine whether or not this configuration change will be reported to the NMS.

Enter yes to report this change to the NMS.

Enter no (default) to prevent this change from being reported to the NMS.

If configuration change notification has been disabled for this modem, configuration
changes are not reported to the NMS regardless of what is entered in this field.

A pop-up menu is available listing valid selections.

Change [Device] Poll List Results Form

A sample Change Poll List results form is shown in Figure 2-15. This results form lists device
information for each specified device and displays the device names and network address of
devices on the updated poll list, along with their polling state (active or skipped).

Figure 2-15. Change [Device] Poll List Results Form

«
...
83
84
85
86
87
...
»

Содержание COMSPHERE 6800 Series














































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для COMSPHERE 6800 Series

Бренд: Maestro Страницы: 4

Бренд: RACOM Страницы: 19

MO128 - QUICK_START_GUIDE

Бренд: SWEEX Страницы: 9

Бренд: Abocom Страницы: 19

Бренд: 3Com Страницы: 56

Бренд: H3 System Страницы: 16

Бренд: Zte Страницы: 15

Бренд: Paradyne Страницы: 2

Бренд: Paradyne Страницы: 4

COMSPHERE 3920PLUS Series

Бренд: Paradyne Страницы: 356

Бренд: TP-Link Страницы: 24

Бренд: Comet64 Страницы: 5

Бренд: Bay Technical Associates Страницы: 27

COMSPHERE 3821Plus

Бренд: Paradyne Страницы: 28

Бренд: Vega Страницы: 27

Бренд: Four-Faith Страницы: 34

Бренд: CTC Union Страницы: 40

Бренд: CTC Union Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды