Paradyne COMSPHERE 6800 Series Скачать руководство пользователя | Manualshive

Страница: 60 / 237

background image

2

Modem/DSU Commands

2-37

6800-A2-GB31-20

January 1997

Slot (Display field)

Displays the number of the new slot location of the device.

Number of device profiles to update (Required field)

Specify whether the profile of only the addressed device should be updated, or whether all
affected device profiles (the addressed device and downstream/associated devices) should
be updated.

Enter 1 to update only the profile of the selected device.

Enter all (default) to update the device profile of the selected device(s) and all
downstream devices.

A pop-up menu is available listing valid selections.

Set CNN event (Required field)

If configuration change notification has been enabled for this device, use this field to
determine whether or not this configuration change will be reported to the NMS.

Enter yes to report this change to the NMS.

Enter no (default) to prevent this change from being reported to the NMS.

If configuration change notification has been disabled for this modem, configuration
changes are not reported to the NMS regardless of what is entered here.

A pop-up menu is available listing valid selections.

Change Address Results Form

The Change Address results form lists device information for the specified device(s).

For a device in ADp mode, the Address field displays the device’s pure serial number address in
the format upstream link level address/serial number.

For a device in DATAPHONE II mode, the Address field displays the device’s original link level
address (prior to the address change).

Figure 2-10 is a sample of the Change Address results form.

«
...
58
59
60
61
62
...
»

Содержание COMSPHERE 6800 Series














































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для COMSPHERE 6800 Series

Бренд: PROLiNK Страницы: 19

MO128 - QUICK_START_GUIDE

Бренд: SWEEX Страницы: 9

Бренд: TP-Link Страницы: 4

Ripwave-MX 2.5-2.6 LMX E

Бренд: Navini Networks Страницы: 40

Бренд: Data-Linc Group Страницы: 15

Бренд: LG Страницы: 21

Бренд: LG Страницы: 40

Бренд: LG Страницы: 63

SmartThinQ LCW-003

Бренд: LG Страницы: 353

ThinQ Wi-Fi MODEM

Бренд: LG Страницы: 16

SmartThinQ LCW-005

Бренд: LG Страницы: 11

Бренд: Siemens Страницы: 25

Бренд: Siemens Страницы: 48

Бренд: Siemens Страницы: 79

Бренд: Racelogic Страницы: 6

Бренд: Elastic Networks Страницы: 32

Бренд: CalAmp Страницы: 62

Бренд: NETGEAR Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды