Paradyne COMSPHERE 6800 Series Скачать руководство пользователя | Manualshive

Страница: 161 / 237

background image

COMSPHERE 6800 Series Network Management System

2-138

January 1997

6800-A2-GB31-20

Display Port Speed(s) (dspsp)

Use the dspsp command to display the port speed configuration of the ports on one or more
COMSPHERE 3400/4400 Series modems with TDM.

For most commands, NMS enables you to specify the destination for the command’s results and
schedule its execution. If the last page of the input form cannot accommodate the Destination for
results and Schedule execution fields, an additional page is provided. For a complete description
of these fields, refer to Chapter 1, Introduction.

Access Level:

Data Technician, Manager, System Administrator

Abbreviation:

dspsp
Alternate: dsportsp

Restrictions:

None

Routine:

Yes

Schedule:

Yes

Related Commands: Change Options (cho)

Change Port Options (chpo)
Display Port Options (dspo)
Change Port Speed(s) (chpsp)

Display Port Speed(s) Input Form

This input form contains the following field:

Device(s) (Required field)

Enter the device(s) whose port speeds are to be displayed. One or more device(s) may be
specified. Standard addressing format applies to the input. For information on device
addressing, refer to Appendix D of the COMSPHERE 6800 Series Network Management
System User’s/System Administrator’s Guide.

Display Port Speed(s) Results Form

Different results forms are displayed depending on the device to which the command is sent.
Figure 2-43 is a sample of Page 1 of the Display Port Speed(s) results form for a 3400/ 4400 Series
modem. The figures in this form display the port speeds associated with a 19.2 kbps modem.

«
...
159
160
161
162
163
...
»

Содержание COMSPHERE 6800 Series














































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для COMSPHERE 6800 Series

Бренд: TP-Link Страницы: 90

Бренд: DareGlobal Страницы: 20

Бренд: Ebyte Страницы: 16

Бренд: XtendLan Страницы: 95

Бренд: CalAmp Страницы: 102

Бренд: Zonet Страницы: 2

Бренд: Data-Linc Group Страницы: 31

Бренд: RadioLabs Страницы: 11

Бренд: Cisco Страницы: 30

Бренд: Jizhuo Technology Страницы: 13

Бренд: Davicom Страницы: 24

Бренд: Technicolor Страницы: 3

Бренд: DCB Страницы: 1

Бренд: BT Страницы: 18

Бренд: NETGEAR Страницы: 266

Бренд: SMC Networks Страницы: 48

Бренд: Elastic Networks Страницы: 30

Бренд: 8x8 Inc Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды