![background image](http://html1.mh-extra.com/html/paradox/sp6000/sp6000_programming-manual_3649980008.webp)
8
Magellan & Spectra SP • Programming Guide
Communicator
Cancel Communication
Keypad Programming
Assigning Keypad Zone Numbers
Assigning Keypad Zone Numbers TM50/TM70
Entry Point Zone Assignment (StayD)
Keypad Input/Output Configuration (K636 V2.0 and higher)
PGMs
Step Action
Details
1
+
installer code
= flash; maintenance code may also be
used
2
-
3
2
= backup phone #
-
3
= personal phone #1
4
= personal phone #2
5
= personal phone #3
6
= personal phone #4
7
= personal phone #5
4
Phone # +
ENTER
Enter phone number (up to 32 digits), and
then press
ENTER
to proceed to the next phone
number, or go to step 5 if option
8
was
selected
Step Action
Details
1
+
installer code
= flash; maintenance code may also be
used
2
-
3
9
Cancels all communication with BabyWare and
GSM module
Step Action
Details
1
E
NTER
+
installer code
ARM
+
STAY
= flash; maintenance code may
also be used
2
Press and hold
for
three seconds
ARM
+
STAY
= ON
3
Zone
ENTER
K35, K32, K32LCD, K32LX = two digits:
01
to
32
;
K636, K10V/H = one digit:
1
to
0
(10)
NOTE:
To erase a keypad zone number, press
CLEAR
, and then
ENTER
.
Step Action
Details
1
Press and hold
MENU
+
installer code
Enters into advanced programming
2
Program this unit
Ensure that zone temperature input is enabled
3
Press keypad zone
number
Select your zone
Step Action
Details
1
E
NTER
+
installer code
ARM
+
STAY
= flash
2
Press and hold
OFF
for
three seconds
ARM
+
STAY
= ON
3
Zone number
K35, K32RF, K37, K32LCD, K32LX = two digits:
01
to
32
; K636, K10V/H = one digit:
1
to
0
(10;
maximum ten zones); the first zone
programmed will be the designated entry
point and will flash; up to three more path
zones can be added – these zones will light up
and remain lit
4
E
NTER
Press
ENTER
to save and exit
Step Action
Details
1
E
NTER
+
installer code
ARM
+
STAY
= flash
2
Press and hold
ENTER
for three seconds
ARM
+
STAY
= ON
3
Option
1
ON = output switches to ground following
system arming (blue wire, maximum150 mA)
OFF
= input (keypad zone input)
4
Option
2
ON = output N.C.
OFF
= output N.O.
NOTE:
When configuring as an output, clear the assigned keypad zone first.
Step Action
Details
1
+
installer code
= flash; maintenance code may also be
used
2
-
3
PGM number
Two digits:
01
to
16
4
Enroll or erase PGM
Wireless PGM = press the
LEARN
/
TAMPER
switch
or remove and re-install Jumper 2 (JP2) on
module; hardwired PGM = press
ENTER
5
PGM type
1
= Follow button
or
2
= Follow button
or
3
=
Follow zone
4
=
Follow alarm
5
=
Follow bell
6
= Follow arm
7
= Follow Stay arm
8
= Follow Sleep arm
6
If PGM type is
1
,
2
,
3
, or
4
, enter activation
delay
1
= Follow
2
= 1 sec.
3
=
5 sec.
4
=
15 sec.
5
=
30 sec.
6
= 1 min.
7
= 5 min.
8
= 15 min.
9
= 30 min.
If PGM type is
5
, proceed
to the next available
PGM
-
If PGM type is
6
,
7
, or
8
,
enter
1
and/or
2
+
ENTER
If system is partitioned, select partition(s), and
then press
ENTER
to proceed to the next available
PGM
7
If PGM type is
1
or
2
,
enter two-digit remote
control #
01 to 32 (00 = all remote controls); the control
panel proceeds to the next available PGM
If PGM type is
3
, enter
two-digit zone #
01 to 32 (00 = all zones); the control panel
proceeds to the next available PGM
If PGM type is
4
, enter
1
and/or
2
+
ENTER
If system is partitioned, select partition(s), and
then press
ENTER
to proceed to the next available
PGM
NOTE:
To erase a PGM, press and hold
SLEEP
for three seconds.
Содержание SP6000
Страница 71: ......