PMD2P-EI01 - Printed in Canada 06/2013
PMD2P: Wireless PIR Motion Detector with Built-in Pet Immunity V1.0
Detector Settings - Quick View
Detector Settings - Details
Sensitivity
S2 (Slider)
High = High sensitivity (
default
)
Low = Low sensitivity
Fast/Slow Mode
JP1 (Jumper)
Off = Slow mode
On = Fast mode (
default
)
LED Feedback
JP2 (Jumper)
Off = Disabled
On = Enabled (
default
)
Sensitivity - S2 (Slider)
High Sensitivity
In high sensitivity mode, you should not be able to cross more than one complete zone (consisting of two
beams - left and right sensor elements) in the coverage area with any kind of movement. Use this setting for
the majority of installations.
Low Sensitivity
In low sensitivity mode, the amount of movement required to generate an alarm is doubled. The use of low
sensitivity mode is recommended in areas where the incidence of false alarms may be greater.
Fast/Slow Mode - JP1 (Jumper)
Slow Mode
Recommended in areas where the incidence of false alarms may be greater.
Fast Mode
Recommended for the majority of installations.
LED Feedback - JP2 (Jumper)
Alarm
The red LED will illuminate for a period of 3 seconds whenever the motion detector detects any kind of
movement.
Low Battery
The PMD2P performs a battery test every 12 hours. If battery voltage drops below a certain level, the red LED
flashes at 8 second intervals and the motion detector will send a low battery signal to the receiver. A trouble is
generated and then transmitted to the central monitoring station.
Signal Transmission
The red LED blinks fast when transmitting.
Description
The Paradox PMD2P is an analog single-optic PIR motion detector with built-in pet
immunity for use with Magellan wireless receivers/transceivers. The PMD2P is immune
to animals weighing up to 18kg (40 pounds), and features automatic temperature
compensation.
The PMD2P is battery-powered and features an innovative three minute energy save
mode (after two detections within a five-minute period). Also, the ALIVE software in
the PMD2P ensures that the alarm LED continues to display when it is in energy save
mode without compromising battery life.
Installation
At the installation height of 2.1m (7ft)
±10%, the PMD2P provides full
coverage from 1.2m (3.9 ft) to 11m (36
ft). Mounting lower than recommended
height will decrease the long range
performance; higher will decrease short
range performance. Do not obscure the
detector, partially nor fully.
IMPORTANT
: Do not touch the sensor
as this could result in malfunction.
Clean the sensor surface using a soft
cloth with pure alcohol. Also, avoid
bending, cutting, or altering the antenna
or mounting the detector near metal as
this may affect transmission.
A
- Corner mount
B
- Flat surface mount
C
- Wall tamper hole
A
B
A
B
A
B
A
C
Dual Tamper Mechanism - Wall and Cover
The PMD2P is equipped with dual tamper protection; an alarm is generated if the front cover is removed or if the detector is removed
from the wall. In order for the wall tamper removal feature to be functional, a screw needs to be inserted in the wall tamper hole (
see
PCB Overview at right
).
Powering the Wireless Detector
Verifying proper polarity, insert three “AAA” alkaline batteries into the motion detector’s battery compartment. To replace the
batteries, remove the old batteries, then press and release the tamper switch and wait 60 seconds in order to re-initialize the unit. After
initialization is complete, insert batteries while verifying proper polarity (verify proper polarity on battery compartment connector as
well).
IMPORTANT
:
Make sure that when reinstalling the battery compartment that the batteries are facing the back-plate.
Power-up Sequence
After inserting the batteries, a power-up sequence begins (lasting 10-20 seconds). During this time, the red LED flashes and the
detector will not detect an open zone or tamper.
Signal Strength Test
In order to verify proper signal reception, perform a signal strength test as described in the receiver’s Reference and Installation
Manual. Prior to performing the test, ensure the batteries have been installed. Also verify that the motion detector has been assigned
to a zone according to the instructions in the receiver’s Reference and Installation Manual. If the transmission is weak, relocating the
transmitter by a few inches can greatly improve the reception.
PCB Overview
Battery
compartment
S2
Antenna
JP1
JP2
Anti-tamper
switch
Battery
connector
Wall tamper
hole