I
NTRODUCTION
The Voice-Assisted Arm/Disarm Bus Module allows the user to arm
or disarm their security system as well as activate or deactivate
In
Touch’s
PGM from any touch-tone telephone. The APR-ADM2
uses detailed voice prompts to guide the user. Due to the Auto-
panel Recognition feature, the
In Touch
can be connected to either
the Spectra (V2.0 or higher) or Digiplex control panels.
T
ECHNICAL
S
PECIFICATIONS
Operating Voltage:
9 - 15VDC
Current Consumption:
Typical: 70mA
Maximum: 105mA (with PGM enabled)
Power Consumption:
1 Watt
PGM Outputs:
1 form “C” relay rated @ 125V, 5A
receptive load
Operating Temperature:
0°C to 50°C (32°F to 122°F)
Compatible Telephone:
DTMF (Touch-tone)
Compatibility:
Any Digiplex control panel
I
NSTALLATION
The APR-ADM2 is connected to Digiplex’s communication bus.
Connect the four terminals labeled “
12
VDC
”, “
GND
”, “
GRN
”, and “
YEL
“
of the APR-ADM2 to the corresponding terminals of the Digiplex
control panel as shown in Figure 1. Please refer to the Digiplex
Reference & Installation Manual
for the maximum allowable
installation distance from the control panel.
Connect
In Touch’s
“
RING
” terminal to Digiplex’s “
R
1
” terminal and
the “
TIP
” terminal of the
In Touch
to the “
T
1
” terminal of the Digiplex
control panel as shown in Figure 1. If the household telephone is
sharing the telephone line with Digiplex and APR-ADM2, connect
the house-hold telephone to the “
R
-1
” and “
T
-1
” terminals of the bus
module as shown in Figure 1.
Connect APR-ADM2’s PGM as shown in Figure 2.
If the control panel is configured to report Arming and
Disarming events and if the
In Touch
and control panel
share the same telephone line, the user’s call will be
interrupted during use.
A
UTO
-
PANEL
R
ECOGNITION
This is a feature that allows
In Touch
to be used with either
Spectra or Digiplex. When connected to the bus, the APR-ADM2
will automatically detect which system it is connected to and adjust
its internal communication parameters accordingly. It allows
In
Touch
to be connected to any Digiplex control panel as well as any
Spectra control panel V2.0 or higher.
If connecting the APR-ADM2 to a Spectra control panel, refer to
the
Spectra APR-ADM2 Reference & Installation Manual
.
P
ROGRAMMING
M
ETHOD
To access the
In Touch
programming mode:
APR-ADM2 can also be programmed using Digiplex’s
Module
Broadcast
feature as well as through the WinLoad Software. Refer
to the
Digiplex Reference & Installation Manual
for more
information on the
Module Broadcast
feature and to
WinLoad’s
Online Help
for information on programming with WinLoad. The
bus module’s serial number can be found on its PC board.
N
UMBER
OF
R
INGS
Section
[001]
[001]
The value (001 to 255, 000 = disabled) programmed in section
[001]
represents the number of rings the APR-ADM2 will wait
before picking-up the line. If the line is not answered after the
number of programmed rings,
In Touch
will answer the call.
Be sure to program the APR-ADM2 module’s number of
rings to be less than the number of rings programmed in the
Digiplex control panel or enter
000
as the number of rings
for the Digiplex.
A
NSWERING
M
ACHINE
O
VERRIDE
Section
[002]
[002]
If the
In Touch
uses a telephone line that uses an answering
machine or service, the Answering Machine Override must be
programmed. The value (010 to 255 seconds, 000 = disabled)
programmed in section
[002]
represents the delay period that APR-
ADM2 will wait between the first and second call. The user calls the
In Touch
, hangs-up, and then calls back within the value
programmed in section
[002]
. If the APR-ADM2 is called back
within the programmed delay period, the bus module will override
the answering machine or service by picking-up the line on the first
ring.
PGM T
IMER
Section
[003]
[003]
When the PGM is activated by a user, the value (001 to 255, 000 =
No Timer) programmed in section
[003]
determines the time that
APR-ADM2’s PGM will remain activated. Once the time value set
in section
[003]
has elapsed, the PGM will deactivate. If a value of
000 is entered into section
[003]
, the PGM will remain activated
until it is manually deactivated by the user.
Option
[4]
in section
[004]
determines whether the PGM
Timer programmed in section
[003]
is in seconds or
minutes.
STEP 1: Press and hold the
[0]
key
STEP 2: Enter the
[
INSTALLER
CODE
]
STEP 3: Enter section
[953]
STEP 4: Enter the APR-ADM2’s 8-digit
[
SERIAL
NUMBER
]
STEP 5: Enter the 3-digit
[
SECTION
]
you want to program
STEP 6: Enter the required data
