background image

© Panduit Corp. 2018 

OPERATION MANUAL 

CT-2002CH

 

 

CT-2002CH: PA29258A01_00   

 

 

Page: 2 of 6 

 

 

 

 

6-2018 

PRECAUTIONS AND GENERAL GUIDELINES 

 

This symbol is used to call your attention to hazards or unsafe practices which could result in an 
injury or property damage.  The signal word, defined below, indicates the severity of the hazard.  
The message after the signal word provides information for preventing or avoiding the hazard. 

 

WARNING

 

Hazards which, if not avoided, COULD result in severe injury or death. 

 

CAUTION

 

Hazards or unsafe practices which, if not avoided, MAY result in injury or 
property damage. 

 

 

 

WARNING

 

Read and understand  all of the instructions and safety information in this manual before 
operating or servicing this tool.

 

 

 

WARNING

 

Electric Shock Hazard: 
 
This tool is not insulated.  When using this unit on or near energized electrical lines, use 
proper personal protective equipment. 

 

 

WARNING

 

Wear eye protection when operating or servicing this tool. 
 
Failure to wear eye protection can result in serious eye injury from flying debris or hydraulic oil.

 

 

 

WARNING

 

Skin Injection Hazard: 
 
Oil under pressure easily punctures skin causing serious injury, gangrene, or death.  If you are 
injured by escaping oil, seek medical attention immediately. 

 

Do not use hands to check for leaks. 

 

Depressurize the hydraulic system before servicing. 

 

 

WARNING

 

Keep hands away from the tool head when crimping. 

 

 

WARNING

 

Do not use solvents or flammable liquids to clean this tool.  Solvents or flammable liquids 
could ignite and cause serious injury or property damage.   
 
Do not use tool in or near a highly flammable or explosive atmosphere and/or materials.

 

Содержание CT-2002CH








Отзывы: